This document explains how to configure the NSClient++ Windows agent and If you wanted to change the default port you would change it with this setting:.
Au sein du répertoire NSClient++ « C:/Programmes/NSClient++/ »
12 janv. 2008 The caveat of monitoring public ports is that they are easy to monitor ... NSClient++ – this agent is installed on a Windows server or ...
Et il faut rajouter l'adresse IP du serveur Nagios avec lequel il va communiquer. Ensuite il faut vérifier la ligne ou se configure le port sur lequel NSClient
NSClient++ qui servira de passerelle permettant la supervision de la machine : NSC++
Net stop nscp. Net start nscp. -> Redémarre le service nscp (NSClient++). Le client est maintenant prêt à être installé et configuré sur tous les postes.
This document will describe how to configure your Nagios XI server to use certificates for firewall-cmd --zone=public --add-port=443/tcp --permanent.
extra steps in setting up Nagios but there are several advantages over using a using public ports NRPE
16 oct. 2014 No there is no need to change your existing Nagios configuration. ... Make sure the “port” option in the [NSClient] section is uncommented ...
NSClient++ installer creates the nsclient ini file with the minimal settings that allow NSClient++ to work (defined by your choices during the installation) To use the options described in this document you will need to populate the nsclient ini file with the additional options
Installing The Agent Log on to the windows machine you wish to install theNSClient++ agent on Run the NSClient++ installer package to start the installation The welcome screen will appear Click Next to continue to the next step Select Generic and click Next to continue Click the Typical button
nsclient ini file with the minimal settings that allow NSClient++ to work (defined by your choices during the installation) To use the To use the options described in this document you will need to populate the nsclient ini file with the additional options
Open the configuration file nsclient ini in a text editor for editing (like Notepad) to continue configuring NSClient++ Under the [/modules] section confirm following lines exist: NSCAClient OR NRDPClient = enabledScheduler = enabledCheckSystem = enabledCheckDisk = enabledCheckHelpers = enabled
On Step 1 you will be asked to supply the address of theWindows machine running NSClient++ Click Next to progress to step 2 On step 2 you will configure all of the options formonitoring To start off with make sure a valid Host Name has beenentered The NSClient++ Agent section has a field for thepassword you provided the NSClient++ installer
See the Cisco Nexus Virtual Services Appliance Software Installation and Upgrade Guide Release 4 2(1)SP1(5 1) for more information You can then make changes to the default flexible network uplink configuration to suit your needs:For example you can add ports to a port channel See Figure 3-3
This document explains how to configure the NSClient++ Windows agent and If you wanted to change the default port you would change it with this setting:
This document describes how to configure NSClient++ to send passive check results to Nagios XI using Nagios Remote Data Processor (NRDP) Nagios Service
Au sein du répertoire NSClient++ « C:/Programmes/NSClient++/ » sélectionnez le fichier de configuration système ini (ce dernier peut changer selon les
The default port for NSClient++ is 12489 Is is possible to change this port and if so where does this change need to be made?
All these ports can be changed so check your nsc ini 5 Windows Firewall 7 Installing NSClient++ This is a grooving process before it was all manual but
Welcome · About NSClient++ NSClient is an agent designed originally to work with Nagios but has since evolved into a fully fledged monitoring agent which can be
8162019 NSClient++ Reference Manual pdf 1152 Table of Contents About NSClient++1 Supported OSPlatform2 Whats in a name3 Sponsorship4 Fans of NSClient++5
After installing NSClient++ you need to configure it If you use NRPEServer (check_nrpe NRPEListener) you need the NRPE port open (usually 5666) from
Net stop nscp Net start nscp -> Redémarre le service nscp (NSClient++) Le client est maintenant prêt à être installé et configuré sur tous les postes
NSClient Agent for Nagios Packet Captures · Edit / Improve This Page! External Links: Nagios (PDF of Ports) Nagios Website NSClient