3.-UNPACKING AND CHECKING EQUIPMENTS. 4.- OPTIONAL ACCESSORIES. 5. -Used to enter information for programming the radio's lists and the.
Contributions taken from: “BaoFeng UV-5R User's Guide” by The Radio Ex: Programming a Channel Repeater Offset with CTCSS Tone.
Contributions taken from: “Baofeng UV-5R User's Guide” by The Radio Ex: Programming a Channel Repeater Offset with CTCSS Tone.
Contributions taken from: “Baofeng UV-5R User's Guide” by The Radio Ex: Programming a Channel Repeater Offset with CTCSS Tone.
With your radio turned off connect your radio to your computer using the Baofeng UV-5R Programming cable. 3. Start CHIRP. 4. Turn on your radio and wait
Also applies to UV-5RA UV-5X3
Uv-82 VIP. Programmer.. Download the Software. USB to Serial Cable.. Visit http:.hb. 3 / 6 ... BaoFeng. UV-5R programming software free download. Code:.
Baofeng UV-5R iii. Table of Contents Attaching the programming cable . ... Originally I intended to include a whole section in the programming chapter ...
Baofeng UV-5R iii. Table of Contents. Preface . Originally I intended to include a whole section in the programming chapter dedicated.
Jul 13 2014 The higher the level
• Use only BAOFENG supplied or approved batteries and chargers Do not use any portable radio that has a damaged antenna If a damaged antenna comes into contact with your skin a minor burn can result • Turn off your radio prior to entering any area with explosive and flammable materials
Baofeng UV-5R Step-by-Step Programming Guide Also applies to UV-5RA UV-5X3 UV-5RAX GT-3 BF-F8 BF-F9 Noji Ratzlaff Set the radio to communicate with a repeater at 146 780– MHz 100 0 Hz 0 Turn on the radio and make sure it’s unlocked 1 VFO/MR (frequency mode) 2 Select the upper display A/B 3 Set the frequency 1 - 4 - 6 - 7 - 8 - 0 4
BaoFeng UV-5R Channel Programming Cheat Sheet 7/19/2018 Key Concepts ALWAYS place the radio in “frequency mode” by toggling the orange [VFO/MR] button ALWAYS set receive and transmit frequency on the top or A line by toggling the blue [A/B] button ALWAYS delete a channel’s content before storing new content
Programming Your Baofeng UV-5R Radio Duplex (Using a Repeater) Manual Programming Guide What You Will Need to Program your Radio: Receive Frequency: ex 146 720 or 449 375 Transmit PL Tone: ex 100 0 Hz or 88 5 Hz Offset Direction: Off + or – (See Step 6) Offset Value: 600 kHz or 5 MHz (See Step 7)
Baofeng UV5R Programming MemoriesManually The following steps must be followed exactly Do NOT skip any steps along the way Programming a Repeater Channel with Standard Offsets This example is for: 146 700 MHz600kHz minus offsetinto channel 99CTCSS tone 123 0 1 Set radio to VFO Mode (Frequency Mode) a ) UV5R/GT3 - Press VFO/MR button b )
Setting up and programming your UV-5R Programming Example 1: storing simplex frequencies Switch to VFO A Select VHF or UHF by using the Band key Select the frequency you want to store Press Menu type ‘27‘ and press Menu again Select an empty memory position (000 – 127) by using the Press Menu again to store the frequency Up or Down key
Programming Your Baofeng UV-5R Manually The Baofeng UV-5R has become one of the most common handheld radios available due to its low cost One of the common issues with this radio is the complexity of manually programming the radio while in the field This document is intended to be used with the manual (which I recommend