(www.cbp.gov) for the latest information on specific laws regulations or Form C1
The Tennessee General Assembly enacted the Tennessee Retailers' Sales Tax Act However if the concrete is purchased for use to construct an electric ...
85167920. ELECTRICAL/ELECTRONIC DEVICES FOR REPELLING INSECTS (E.G.MOSQUITOES ETC). NOS. 85. 851680. ELECTRIC HEATING RESISTORS.
The requirements of this Code should therefore
electrical installation services of illumination and signalling systems for roads railways
DCSF would like to thank the following for their help and advice: Kathie Bull. Educational consultant. Steve Clow. PB&R Design Services Hampshire County
The International Programme for the Improvement of Working Conditions and Environment (PIACT) was launched by the International Labour Organisation in 1976
Women lead the way in community-based child nutrition in rural Tanzania by Scholastica lower costs
03-Jan-2014 used for fuel or lighting purposes in buildings. ... advice on artistic questions in connection with building schemes.
Use of the Nice Classification is mandatory not only for the national registration of marks in countries party to the Nice Agreement but also for the
Carefully slide gasket over float arm and sending unit to fit flat against underside of mounting plate Install completed unit into tank by carefully inserting float arm and then sender through the tank hole Avoid bending float arm as this may cause the sending unit to give improper readings
TANK AREA FREE FROM SPARKS AND FLAMES EMPTY TANK OF FUEL AND FUMES BEFORE CONTINUING WITH INSTALLATION PROPER WIRING INSTALLATION: 1 Connect sender(s) wire from fuel gauge to the threaded terminal on sender 2 Connect ground wire to 1/4" fasson terminal on sender Elec ic F el Se de Page 2 Figure 3 Figure 4
E FUEL PUMP AND SENDER ASSEMBLY INSTALLATION Replace and position assembly in tank; use new gasket provided Install cam locking ring and tighten Reconnect hoses and electrical connectors Reconnect battery and refill tank Start car and inspect hose connections and sender unit gasket for fuel leaks
setting the sender type installation good engine ground + 12v connection red black + 12v dash lighting for thru-dial lit gauges only (not used on gauges that accept incandescent bulb for lighting) connect to fuel level sender (make sure sender is grounded) white purple fuse (see caution left) black brown radio shack 275-1556 (optional) caution!
With VDO fuel tank senders (Part #226 001) an empty tank will read 10W As fuel is added the resistance reading will rise until With the key on pull the sender wire off of the sender: Fuel and pressure gauges: Temperature gauge: b) the tank is full when it will read 180W needle to the right-hand position
PROPER WIRING INSTALLATION: -Connect ground (pink) wire from the KUS sending unit to a common grounding hook-up -Connect (black) wire from the KUS sending unit to gauge hook-up If your gauge has color coded hook-ups maintain this coding as you connect the sender and ground wires WARNING!! GASOLINE IS EXTREMELY FLAMMABLE
4 Using 18-ga wire connect the (S) sender terminal of the gauge to the pressure sender 5 Connect the light wire to the dash lighting circuit or to a +12V switched circuit 6 Double check all connections then reconnect the negative (-) battery cable & test instrument to ensure that it is working PRESSURE SENDER INSTALLATION:
With the gasket in place below of the flange carefully feed the float arm and sender body into the 1 697" (43mm) hole in the tank Make certain the float arm has free motion with the tank Using the sender flange as a template locate the positions of the five mounting holes
install the sender 6 RefertoFigure 3 Route a length of 18-gauge insulated copper wire from the gauge to the sender connect the wire to the sender onnect the other end of the wire to the connection post on the back of the gauge marked “S” 7 Make sure the fuel level sender is grounded to ground on fuel tank or to the same point as fac
Fuel Sender Installation For tank depths of 6” to 15-1/2” it will be necessary to remove the lower mounting bracket Begin by removing the two screws and nuts from the lower mounting bracket These will be discarded Remove the two screws from the plastic rheostat housing Save these screws to use later
INSTALLATION INSTRUCTIONS SHORT SWEEP ELECTRIC FUEL LEVEL GAUGE 2650-1858-77 Wiring: Sending Unit Wiring: Gauge Mounting: Gauge to Sender Compatibility: Looking at the rear of the gauge you will have 3 terminals labeled S I & GND You may use 18g or 20g stranded wire for all fuel level gauge wiring S = This connects to the sending unit in
- Install your electric fuel sendergently inserting float arm into tank followed by sending unit Align screw holes between gasket mounting plate and tank - Secure sending unit to tanktightening mounting screws into place just until white sealant shows beneath the screw head