OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If the transducer came with a connector do not remove it to ease cable routing If the cable must be cut and spliced use Airmar's splash-proof |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If your transducer came with a connector do not remove it to ease cable routing If the cable must be cut and spliced use Airmar's splash-proof |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If your transducer came with a connector do not remove it to ease cable routing If the cable must be cut and spliced use Airmar's splash-proof |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If the transducer came with a connector do not remove it to ease cable routing If the cable must be cut and spliced use Airmar's splash-proof |
On outboard and sterndrive vessels , you should mount the transducer in front of and close to the engine or engines.
On inboard vessels , you should mount the transducer in front of and far away from the engine propeller and shaft.
On single-drive boats, you should not mount the transducer in the path of the propeller.
A better option uses a piece of "plastic wood" such as structural grade Starboard as a mounting point.
Cut a piece long enough to extend from the bottom of the transom to a point at least six inches above the waterline, and several inches wider than the mount.
Thru-bolt it to the transom using four stainless bolts.
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If your transducer came with a connector do not remove it to ease cable routing. If the cable must be cut and spliced |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
NOTE: Lubricate the O-ring with petroleum jelly before sliding it onto the transducer assembly. Copyright © 2005 - 2010 Airmar Technology Corp. boss (2). Page 4 |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
Using a 5mm #4 |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
Transom Mount with Integrated Release Bracket. Depth Transducer with Temperature Sensor. Depth & Temperature Model: P66. TRIDUCER® Multisensor: P66. |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If the transducer came with a connector do not remove it to ease cable routing. If the cable must be cut and spliced |
Importance of Proper Transducer Selection & Installation
Regardless of mounting style a properly installed transducer delivers a vertical beam that aims straight down toward the bottom |
AIRMAR
Benefits of Pocket Mount Transducers transducers are installed within a small custom pocket ... performance of an AIRMAR Chirp-ready transducer. |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
CAUTION: If your transducer came with a connector do not remove it to ease cable routing. If the cable must be cut and spliced |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
Airmar High-Performance Fairing has a long streamlined shape directing water around the transducer to minimize drag. Performance is excellent above 15kn (18MPH) |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
Patent http://www.airmar.com/patent.html CAUTION: Chirp transducer—Do not install in the ... transducer inside the hull at the mounting location. |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS - AIRMAR
The tilt angle is printed on the top of the transducer (Figure 1) To measure the deadrise angle of your hull at the selected mounting location, use an angle finder or |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS - AIRMAR
Mounting the transducer on the side of the transom where the propeller blades are moving downward is preferred (Figure 1) Mount the transducer as close to the centerline (keel) of the boat as possible to ensure the transducer's face remains in the water when the boat is turning |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS - AIRMAR
Place the transducer inside a thin plastic bag Partially fill the bag with water and close it tightly with a cable tie Wet the surface of the hull and press the active face of the transducer against it through the bag (Figure 3-B) |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS - AIRMAR
Operating in air will allow the transducer to overheat resulting in failure CAUTION: Bronze transducer—Never mount a bronze housing in a metal hull, because |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS - AIRMAR
OWNER'S GUIDE INSTALLATION INSTRUCTIONS 17 -0 10 re v 1 2 03 /15 /16 In-Hull Trolling Motor Puck Transducer Models: P50, P72, P76, P78, |
INSTALLATION INSTRUCTIONS OWNERS GUIDE &
CAUTION: TM150M CHIRP transducer—Always CAUTION: Never strike the transducer with anything spliced, use Airmar's splash-proof Junction Box No |
INSTALLATION INSTRUCTIONS OWNERS GUIDE &
Bonding material (see www airmar com for additional brands): Fiberglass resin not mount the transducer near water intake or discharge open- ings; or behind |
OWNERS GUIDE & INSTALLATION INSTRUCTIONS
However, carefully selecting the transducer mounting location can After testing, wipe all traces of the lubricant from the transducer's face 2 AIRMAR® inboard |
[PDF] owners guide & installation instructions - Airmar
Place the transducer against the hull and allow bilge water to cover the surface where they touch (Figure 3 A) B For a moderate deadrise angle—If the hull surface is not smooth, grind it with a disc sander Place the transducer inside a thin plastic bag |
[PDF] owners guide & installation instructions - Airmar
Never install a plastic housing in a wood hull since swelling of the wood may Guidelines CAUTION Do not mount the transducer in line with or near water |
[PDF] owners guide & installation instructions - Airmar
The tilt angle is printed on the top of the transducer (Figure 1) To measure the deadrise angle of your hull at the selected mounting location, use an angle finder |
[PDF] Installation Instructions - Gemeco Marine Accessories
Stuffing Tube After determining the best mounting location for the transducer, The information needed to order a replacement Airmar transducer is printed on |
[PDF] Installation Instructions - Defender Marine
CAUTION Bronze transducer—Never mount in a metal hull, because the transducer's face • Airmar High Performance Fairing has a long streamlined shape |
[PDF] Transom Mount Chirp Transducers - NautiBoutique
The Benefits of AIRMAR's Chirp ready Transducers • One broadband transducer covers up to 117 kHz of bandwidth – greater opportunities to detect fish in the |
[PDF] Garmin Transducer Selection Guide-2020
Available with trolling motor, transom and thru hull mount transducer options Airmar TM150M Entry level CHIRP solution Requires separate install kit for |
[PDF] 17-299-02-rev06-TM258 plastic brktfm
CAUTION Avoid mounting the transducer where the boat may be supported during the cable must be cut and spliced, use Airmar's splash proof Junction Box |
[PDF] Pocket/Keel Mount Chirp Transducers - Blue Bottle Marine
AIRMAR®, DEFINING CHIRP TECHNOLOGY Page 2 Courtesy of Raymarine Benefits of Pocket Mount Transducers |
Source: Manualzz
Source:https://cdn.echomastermarine.co.uk/assets/manuals/Airmar/Transducers/_resampled/P58%20Installation%20Manual.png
Source:https://data2.manualslib.com/first-image/i17/82/8136/813594/airmar-m260.png
Source:https://img.nauticexpo.com/pdf/repository_ne/22646/several-installation-methods-wide-beam-chirp-transducers-77159_1mg.jpg
Source:https://img.nauticexpo.com/pdf/repository_ne/22646/pm265-lm-lh-chirp-122632_1mg.jpg
Source:https://s1.manualzz.com/store/data/009453741_1-fc7171a85f2860b500c453278d9390c8.png