Refer to the Cisco IOS command reference book for your Cisco IOS release for further information on the additional arguments and keywords that can be used with these commands. Enters privileged EXEC mode. Enter the password when prompted. Enters global configuration mode.
See the Cisco IOS XE Privilege Levels for more information on privilege levels and the privilege command. In general, the user EXEC commands allow you to connect to remote devices, change terminal line settings on a temporary basis, perform basic tests, and list system information.
Cisco devices use privilege levels to provide password security for different levels of switch operation. By default, the Cisco IOS XE software operates in two modes (privilege levels) of password security: user EXEC (Level 1) and privileged EXEC (Level 15). You can configure up to 16 hierarchical levels of commands for each mode.
The password is not encrypted and provides access to level 15 (traditional privileged EXEC mode access): This example shows how to configure the encrypted password $1$FaD0$Xyti5Rkls3LoyxzS8 for privilege level 2:
Controlling Switch Access with Passwords and Privilege Levels
Security Configuration Guide Cisco IOS XE Release 3SE (Catalyst 3650 encrypted password that users must enter to access privileged EXEC mode (the ... |
Controlling Switch Access with Passwords and Privilege Levels
Security Configuration Guide Cisco IOS XE Release 3SE (Catalyst 3850 encrypted password that users must enter to access privileged EXEC mode (the ... |
Lab 3.1.3 Configuring Router Passwords – Instructor Version 2500
Configure a secret password for privileged EXEC mode. GAD(config)#enable password cisco ... Enter cisco but the characters will not be seen on the. |
Using the Command-Line Interface
contained in user EXEC mode as well as the configure privileged EXEC command If your system administrator has set a password |
Controlling Switch Access with Passwords and Privilege Levels
By default the Cisco IOS software operates in two modes (privilege levels) of password security: user EXEC. (Level 1) and privileged EXEC (Level 15). You can |
Controlling Switch Access with Passwords and Privilege Levels
encrypted password that users must enter to access privileged EXEC mode (the default) Cisco switches (and other devices) use privilege levels to provide ... |
User Security Configuration Guide
Cisco IOS XE Password Configuration 25. How To Configure Security with Passwords Privileges and Logins 26. Protecting Access to User Exec Mode 26. |
Controlling Switch Access with Passwords and Privilege Levels
Catalyst 2960-X Switch Security Configuration Guide Cisco IOS Release encrypted password that users must enter to access privileged EXEC mode (the ... |
Controlling Switch Access with Passwords and Privilege Levels
Use Cisco Feature Navigator to find information about platform support and encrypted password that users must enter to access privileged EXEC mode (the ... |
Controlling Switch Access with Passwords and Privilege Levels
Consolidated Platform Configuration Guide Cisco IOS XE 3.7E and Later encrypted password that users must enter to access privileged EXEC mode (the ... |
Controlling Switch Access with Passwords and Privilege - Cisco
encrypted password that users must enter to access privileged EXEC mode (the default) or any privilege level you specify We recommend that you use the |
Recovering a Lost Enable Password - Cisco
Note You can recover a lost enable password, but not a password that you configured with the enable From user EXEC mode, display the existing configuration register value: The prompt changes to the privileged EXEC prompt: router# |
Configuring Security with Passwords, Privileges, and Logins - Cisco
The default configuration of a Cisco IOS software-based networking device allows you to configure passwords to protect access only to user EXEC mode (for local |
User Security Configuration Guide - Cisco
Cisco IOS XE Password Configuration 25 How To Configure Security with Passwords Privileges and Logins 26 Protecting Access to User Exec Mode 26 |
Controlling Switch Access with Passwords and Privilege - Cisco
Both commands accomplish the same thing; that is, you can establish an encrypted password that users must enter to access privileged EXEC mode (the default) |
User Security Configuration Guide, Cisco IOS Release 15SY
How to Configure Security with Passwords, Privileges, and Logins 22 Protecting Access to User EXEC Mode 22 Configuring a Password for Remote CLI |
User Security Configuration Guide, Cisco IOS XE Release 3E
A Misconfigured Privileged EXEC Mode Password Has Not Been Saved 35 Configuration Examples for Configuring Security with Passwords Privileges and |
Lab 313 Configuring Router Passwords – Instructor Version - UTEZ
Configure a secret password for privileged EXEC mode mode: GAD(config)# enable password cisco Enter cisco but the characters will not be seen on the |
[PDF] Controlling Switch Access with Passwords and Privilege - Cisco
encrypted password that users must enter to access privileged EXEC mode (the default) or any privilege level you specify We recommend that you use the |
[PDF] Configuring Security with Passwords, Privileges, and Logins - Cisco
Privileged EXEC mode also provides access to configuration modes through the configurecommand, and includes advanced testing commands, such as debug |
[PDF] Controlling Switch Access with Passwords and Privilege - Cisco
encrypted password that users must enter to access privileged EXEC mode (the the Cisco IOS software operates in two modes (privilege levels) of password |
[PDF] Recovering a Lost Enable Password - Cisco
Note You can recover a lost enable password, but not a password that you configured with the enable From user EXEC mode, display the existing configuration register value The prompt changes to the privileged EXEC prompt router# |
[PDF] Configuring Local Authentication - Cisco
Command or Action Enables privileged EXEC mode enable Step 1 Example • Enter your password if prompted Router> enable Enters global configuration |
[PDF] User Security Configuration Guide, Cisco IOS Release 15SY
A Misconfigured Privileged EXEC Mode Password Has Not Been Saved 22 Configuration Examples for Configuring Security with Passwords, Privileges, and |
[PDF] Cisco IOS XE Password Configuration
A Misconfigured Privileged EXEC Mode Password Has Not Been Saved 44 Configuration Examples for Configuring Security with Passwords Privileges and |
[PDF] Lab 313 Configuring Router Passwords – Instructor Version - UTEZ
GAD#disable Step 9 Enter the privileged EXEC mode again This time a prompt for a password will show Enter cisco but the characters will not be seen on the |