INSTALLATION GOLDen GATE Trend, TBLZ-1/2/3-1-4-41

INSTALLATION. GOLDen GATE Trend TBLZ-1/2/3-1-4-41. 1. General. Communication unit TBLZ-3-1-4-41. Intended for use together with Version C/D GOLD air.

INSTALLATION. GOLDen GATE Trend TBLZ-1/2/3-1-4-41. 1. Generelt. Kommunikationsenhed TBLZ-3-1-4-41. Beregnet til brug til luftbehandlingsaggregat GOLD ver-.

INSTALLASJON. GOLDen GATE Trend TBLZ-1/2/3-1-4-41. 1. Generelt. Kommunikasjonsenhet TBLZ-3-1-4-41. For bruk til luftbehandlingsaggregat GOLD versjon C.

InSTaLLaTIon. GoLDen GaTE Trend TBLZ-1/2/3-1-4-41. 1. Allmänt. Kommunikationsenhet TBLZ-3-1-4-41. Avsedd att användas till luftbehandlingsaggregat GOLD.

For installation and connection see the function guide for MIRU Pressure sensor Supply air duct Pressure sensor Extract air duct Figure 3 Note: In some cases you might need to cut the measurement tappings to shorten them They should not protrude more than 10 mm from the inner wall inside the duct Function Switch no (1=ON 0=OFF) 1 2 3 4 5

The TBLZ-1-31-1 is designed for installation in the supply air and is used for the dehumidification or humidification function The TBLZ-1-31-2 is designed for installation in the extract air and is used for the dew-point compensation function with cooling beams the dehumidification or humidifica-tion function 2 Installation

1: For CPVC True Lug Valve Overhaul Kit add a “C” to the end of the part number shown (e g BFT-BOK-015C) Ongoing Butterfly Valve design improvements have resulted in variations to repair kits Standard cata- loged kits are for current 72 part number series dry-stem type valve revision

in 1-3/4 1-7/8 2-1/2 3 21 2-1/2 3 3-3/4 3-1/4 3-3/4 4-1/2 4 4-1/2 5-1/2 (mm) (44) (48) (64) (76)(51) (95) (83) )95) )114) (102) (114) (140) Min hole depth h o in 2 2 2-3/4 3-1/4 2-1/41 2-3/4 3-1/4 4-1/4 3-3/4 4-1/4 4-3/4 4-1/4 4-3/4 5-3/4 (mm) (51) (51) (70) (83)(57) (108)(95) (121) (146) Installation torque carbon steel1 T inst ft-lb 4 30

1 2 3 Note that the IQ recommended limits may need to be changed to suit mains supply voltage and auxiliary supply loading or a 24 Vdc regulated supply can be used Assemble sensor unit Setup Strategy Test For full installation details see TB/TS Installation Instructions TG200604 TB/TS/K Installation Instructions TG200607 TB/TS/KO

EN61010-1 It has a 4 point mounting to facilitate installation There is no need to open the unit for normal use and maintenance Input power: 230 Vac or 24 Vac 50/60 Hz If one side of the 24 Vac input power is connected to earth (ground) ensure correct polarity For the UL rating the input power connections must be

This document serves as a comprehensive list of CALEA Standards for Law Enforcement Agencies Those highlighted constitute the contents of the CALEA Law Enforcement Accreditation Program The CALEA Advanced Law Enforcement Accreditation is composed of all standards listed

Using a rubber mallet drive Fe26 Gate Uprights into the rails • Using a drill and 10mm driver bit install 1-10mm self drilling screw into each corner Install the screw inside of the Fe26 Gate Upright so that all screws are hidden • Install supplied 1-1/2” Pressed Dome Caps on installed gate • Maximum gate width is 48”

Redapt PD-E4 series of stopping plugs provide a method of blanking off unused entries in hazardous area approved equipment whilst ensuring the integrity and Ex approval of the installation is maintained Manufactured to facilitate easy installation they are also supplied as standard with a nitrile O-ring seal

%20Globe%20Check.pdf

Using a 7mm socket remove the 4 screws that secure the rear door panel in place Remove Rear door Cover plates behind door handle and in bottom of grab handle to access mounting screws Once panel pins are out lift up on panel Lift panel up and off of door 2 1 1 2 3 3 Pry all panel fasteners loose Start at door hinge side

5 > 601 615 513 610 611 612 614 613 616 208 211 a n g e l 3 d r d u r e l l l n w i l s h i r e p s t c o v e l o c t mou nt ia v ew dr del rey ave d el r y av mountain view dr mou nta iv ew dr