Installationsanleitung T8 LED-Tubes mit Starterüberbrücker 1

Installationsanleitung T8 LED-Tubes mit Starterüberbrücker. 1. Allgemeines. Vor Installation der LED-Tubes ist die derzeitige Anschlussvariante der Leuchten 

Installationsanleitung T8 LED-Tubes mit Starterüberbrücker 1 Allgemeines Vor Installation der LED-Tubes ist die derzeitige Anschlussvariante der Leuchten zu überprüfen Hierzu sind die Hinweise in 2 Vorbereitung der Installation zu beachten Die Installation von LED-Tubes darf nur im spannungsfreien Zustand und nur von

to install the LED T8 tube please read the entire installation guide carefully Ensure that package includes: installation guide warning label to be attached to luminaire LED T8 tube and LED dummy starter Product is not intended to be used with dimmers and emergency light luminaires

Dec 17 2020 · Table #1 – T8 LED Tube – Type A or Type A/B Hybrid - Page 1 of 2 IMPORTANT NOTICE: This list is based on testing performed using a stable AC power supply under laboratory conditions which may not be represen tative of particular end-use conditions

T8 12T8/COR/48-840/MF18/G 10/1 Philips MainsFit (UL Type B) CorePro T8 LED tubes deliver high-quality flicker free performance at an affordable price The UL Type B LED tubes are designed with easy installation and long-term maintenance simplicity in mind Upgrade your lighting to Philips and realize 50000 hour LED lifetime backed by a 5-year

1: Switch off the electricity supply 2: Remove the conventional lamp 3: Remove the starter 4: Stick the warning label in a visible location 5: Click the LED replacement starter into the starter holder 6: Insert the LED Tube into the lampholder 7: Secure the position by turing the lamp by 90° 8: Switch on electricity and check for

T8 LED Tube Installation Instructions 1 Turn off power 2 Remove old Fluorescent tubes 3 Access the ballast by removing ballast cover 4 Disconnect and cut wires feeding to the ballast input (live and neutral wires) they should remain as long as possible 5

installation instructions led lamp luminaire marking labels the t8 led tubes are intended to retrofit listed surface mounted type non-ic or type ic recessed mounted fluorescent luminaires with or without diffuser for maximum four lamps with lamp to lamp distance 11 cm minimum; or retrofit surface mounted listed fluorescent luminaires

1 Coupez l’électricité 2 Retirez la lampe ?uorescente existante 3 Retirez le démarreur ?uorescent existant 4 Insérez le démarreur T8 LED 5 Insérez le tube LED 6 Branchez l’alimentation de V-TAC LED Démarreur LED Ballast inductif AC:220-240V 50Hz AC:220-240V 50Hz LA GAUCHE LA GAUCHE DROITE DROITE (L) (N) V-TAC ENTRÉE V-TAC

The T8 LED tube must not be installed in rainy wet dusty and combustible environment Please confirm whether the light fixture meets the protection requirements 2 Installation Requirements The installation job should be done by electrician or experienced people The operating temperature is -20??+40? 3 Dimension 589mm

Installationsmöglichkeiten 1 2 Umrüstung einer KVG-Leuchte gemäß EN 62776 Ersetzen der T8-Leuchtstofflampe und des eingebauten Starters durch SubstiTUBE®T8 EM und SubstiTUBE®Start Alternativ kann auch die SubstiTUBE®T8 Universal und SubstiTUBE®UN-Start für KVG-Leuchten verwendet werden 1 3 Direktverdrahtung einer EVG oder KVG-Leuchte