cisco switch set time ntp
Configuring NTP
The Network Time Protocol (NTP) synchronizes timekeeping among a set of distributed time servers In this configuration switch 1 and switch 2 are NTP peers |
How do I sync time on a Cisco switch?
On Cisco routers, you can use the show ntp associations command to see the status of NTP peers.
There is a considerable amount of information in the output, which includes packet loss information.
This information is intended to supplement the information available in the Cisco IOS® Command Reference .
Configuring NTP
Send document comments to nexus1k-docfeedback@cisco.com. 8-1. Cisco Nexus 1000V System Management Configuration Guide Release 4.0(4)SV1(1). |
Configuring NTP
Configuring NTP. This chapter describes how to configure the Network Time Protocol (NTP) on the Catalyst enterprise. LAN switches. |
Configuring NTP
You can configure NTP to use a specific source IP address. SUMMARY STEPS. 1. switch# configure terminal. 2. [no] ntp source ip-address. Cisco Nexus |
Configuring NTP
Configuring NTP. This chapter describes how to configure the Network Time Protocol (NTP) on CIsco MDS 9000 Family switches. • Information About NTP page 1. |
Configuring NTP
Cisco ME 1200 Series Carrier Ethernet Access Devices NID Configuration Guide Cisco IOS 15.6(1)SN and Later Releases -Configuring NTP. |
Configuring NTP - Cisco
Figure 8-1 displays a network with two NTP stratum 2 servers and two switches. Page 2. 8-2. Cisco Nexus 1000V System Management Configuration Guide Release 4.0 |
Configuring NTP
Manually distribute NTP authentication keys on the NTP server and Cisco NX-OS devices across the network. • If you are using the switch as an edge device and |
Configuring NTP
Configuring NTP. This chapter describes how to configure the Network Time Protocol (NTP) on Cisco MDS 9000 Series switches. • Information About NTP on page |
System Time Commands
When you enable and synchronize the system time clock using an NTP server you must reboot the Cisco. Enterprise NFVIS so that the BMC or CIMC date and time |
Configuring NTP - Cisco NX-OS
Manually distribute NTP authentication keys on the NTP server and Cisco NX-OS devices across the network. • If you are using the switch as an edge device and |
Configuring NTP - Cisco
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2948G-GE-TX, and Catalyst 2980G Switches Command Reference This chapter consists of these sections: • |
Configuring NTP - Cisco
Configuring NTP This chapter describes how to configure the Network Time Protocol (NTP) on CIsco MDS 9000 Family switches • Information About NTP, page |
Configuring NTP - Cisco
configure terminal Enter global configuration mode ntp server ip-address [version number] [key keyid] [source interface] [prefer] Configure the switch system clock to synchronize a peer or to be synchronized by a peer (peer association) |
Configuring NTP - Cisco
switch# configure terminal switch(config)# feature ntp switch(config)# copy running-config switch# configure terminal You can specify a different stratum level from which NTP clients get their time synchronized switch(config)# show running-config ntp switch(config)# copy running-config switch# configure terminal |
Configuring NTP - Cisco
This figure displays a network with two NTP stratum 2 servers and two switches In this configuration, the switches were configured as follows: • Stratum-2 Server- 1 |
Configuring NTP - Cisco
Figure 8-1 displays a network with two NTP stratum 2 servers and two switches Figure 8-1 NTP Peer and Server Association In this configuration, switch 1 and |
Configuring NTP - Cisco
Cisco Nexus 5000 Series NX-OS System Management Configuration Guide, Release 5 0(3)N1(1) -Configuring NTP |
NTP Configuration Mode Commands - Cisco
The NTP Configuration Mode is used to manage the Network Time Protocol (NTP ) options active ASR 5000 SMC or ASR 5500 MIO will synchronize with external sources NTP sources, or other Stratum 2 or 3 servers, switches or routers) |
NTP on Nexus 7000 Series Switch Configuration Example - Cisco
The Network Time Protocol (NTP) synchronizes the time of day among a set of distributed time servers and clients so that you can correlate events when you |
Configuring NTP - Cisco
The following figure shows a network with two NTP stratum 2 servers and two switches Figure 1: NTP Peer and Server Association In this configuration, switch 1 |