JUMPER SETTINGS
Cloud CX263 Jumper Settings
25 Mar 2014 Cloud CX263 Jumper Settings. Ref. Description. Default Location. Notes. J1. Mic 1 phantom power. OFF. Rear right: Lower PCB. |
Basic jumper settings for Maxtor ATA Hard Drives
Please review these jumper settings prior to installing your new hard drive into your computer. You may want to review more detailed information about the |
Basic jumper settings for IBM DeskStar ATA Hard Drives
Please review these jumper settings prior to installing your new hard drive into your computer. You may want to review more detailed information about the |
RC2014 Pro Jumper Settings
Use double header pins on this module. All four jumers to right hand setting. Top 3 jumpers set start address to 0x0000. Bottom jumper sets lower 32k to be |
Cloud CX261 Jumper Settings
25 Mar 2014 Cloud CX261 Jumper Settings. Ref. Description. Default Location. Notes. J1. Mic 1 phantom power. OFF. Rear right: Lower PCB. |
Fireball ST
Using the jumper pins you can establish the drive Master/Slave configuration. Fireball ST. Jumper Settings. Page 2. Fireball ST. |
LPS 52/80/105
SCSI Jumper Settings. 1 of 1. Configuration Guide. Jumper Settings. Set SCSI ID Note: LPS SCSI does not use a jumper to determine termination. |
Basic jumper settings for Seagate Barracuda ATA Hard Drives
Please review these jumper settings prior to installing your new hard drive into your computer. You may want to review more detailed information about the |
Cloud 46-50 Jumper Settings
25 Mar 2014 Cloud 46-50 Jumper Settings. Ref Description. Default Location. Notes. J1. Mic1 Phantom. OFF. Rear right: Lower PCB. J2. Mic2 Phantom. |
Barracuda 7200.7 Plus Barracuda 7200.7
Use this jumper setting only if the drive does not work as a master with no jumpers installed. Figure 1. Master/slave jumper settings. |
How to physically install, set jumper settings, and set up a Serial
change the default jumper setting in order to use the drive Serial ATA (SATA) I, II, and 6 Gb/s Hard Drive Jumper Settings for 3 5" drives: Important: Caviar |
68 Pin Jumper Settings - Seagate
The following describes the jumper options and settings available on the Maxtor ® Atlas™ V disk drive The Atlas V was developed by the Quantum Corporation |
Western Digital Hard Drive Jumper Settings
Basic jumper settings for Western Digital ATA Hard Drives Thank you for purchasing your new ATA hard drive from Other World Computing Please review these |
34 Jumper Settings - Fujitsu
Figure 3 9 shows the location of the jumpers to select drive configuration and functions Figure 3 9 Figure 3 11 Jumper setting of master or slave device Note : |
C141-E069-02EN 3 - 12 34 Jumper Settings 341 Location of
Jumper Settings 3 4 1 Figure 3 13 shows the location of the jumpers to select drive configuration and Figure 3 15 Jumper setting of master or slave device |
IDE Jumper Settings and Locations - ps-2
The configuration jumpers on both hard drives are set the same The jumpers are preset for cable-select installation Cable-select comparable hard drives and IDE |
Jumpers, Switches, and Connectors
change jumper settings on your system board; you may also need to change To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto |
WD SATA Internal Hard Drive Quick Install Guide
hardware configuration and operating system Default setting is disabled or no jumper shunt placed on For more information on these advanced settings, |
Western Digital Jumper settings - Supreme Law Firm
On SATA hard drives, jumper settings enable or disable enterprise-level features Setting the jumpers correctly on a hard drive requires the proper placement of a |
Western Digital Hard Drives Installation Guide - RS Components
Identify your drive configuration and jumper your new Western Digital hard drive to the recommended setting NOTE: Both Master/Slave and Cable Select |