check_nrpe error receiving data from daemon
|
NRPE Troubleshooting and Common Solutions in Nagios XI
CHECK_NRPE: Error receiving data from daemon(SSL on but not used too short timeout). VII. NRPE: Unable to read output (path in nrpe.cfg wrong). |
|
Nagios XI Log Locations and Descriptions
You can enable logging in. /usr/local/nagios/etc/pnp/process-perfdata.pl with "LOG_LEVEL = 1". This log will contain any timeout errors for performance data |
|
Nagios Core Version 3.x Documentation
with an underscore and are not processed internally by the Nagios daemon. internal data structures and object (e.g. host and service) relationships. |
|
Opengear User Manual 4.21.pdf
Receive Data. Input. 7. DCD. Data Carrier Detect. Input. 8. DSR. Data Set Ready. Input. 2.4.3 Cisco RJ45 pinout (option -X2). The ACM5000 ACM5500 |
|
Opengear User Manual
9 avr. 2013 Data Center and Remote Site Management - User Manual. 10.2.1 Set up central Nagios server. 212. 10.2.2 Set up distributed Opengear console ... |
|
Shinken Documentation
14 août 2015 problem that I see with doing this is that it makes Nagios less ... daemons Receiver daemons |
|
User Manual
Data Center and Remote Site Management – User Manual. 5. SERIAL PORT HOST |
|
Shinken Documentation
16 oct. 2014 Shinken is a monitoring tool compatible with Nagios configuration ... daemons |
|
Nagios Core Documentation
with an underscore and are not processed internally by the Nagios daemon. internal data structures and object (e.g. host and service) relationships. |
|
XCAT3 Documentation
9 mars 2017 All the data for the xCAT Objects (node group |
|
NRPE Troubleshooting and Common Solutions in Nagios XI
This error is not to be confused with the error “CHECK_NRPE: Received 0 bytes from daemon” as they have separate causes Most often, this error is experienced when passing the no ssl switch (-n) to check_nrpe even though NRPE on the remote host was compiled with ssl enabled |
|
CHECK_NRPE: Error - Could Not Complete SSL Handshake
Handshake · NRPE - CHECK_NRPE: Error Receiving · Data From Daemon Problem Description This KB article addresses the following NRPE error: |
|
Monitor remote linux server using Nagios NRPE CentOS Linux
I have observing the following 2 errors Please give me the solution 1 CHECK_NRPE: Error receiving data from daemon 2 NRPE: Command ' check_load' not |
|
Nagios Documentation - Network Startup Resource Center
NRPE - Daemon and plugin for executing plugins on remote hosts notifications getting sent out when no problem notification was sent out to begin with You can now process performance data by executing external commands and/or |
|
Distributed Monitoring, Redundancy, and Failover
and a daemon that runs on your central Nagios server mally would with active checks, that the incoming data represents the true state of the configure a command that returns a status code and an error message just like a normal plug - in |
|
Add-ons and Enhancements - SciTech Connect
an NRPE daemon running on a remote server and we assume that check_nrpe receive data from FILE2SOCK or NDOMOD directly and populate a database with the If you see an error message, you might need to download and compile |
|
Nagios Core Administ - doc-developpement-durableorg
the problem of not being able to check system properties directly over the PING sparta naginet (10 128 0 21) 56(84) bytes of data With this done, the next time our host changes its state, we should receive messages similar configuration is broken, then the Nagios Core daemon will keep running with the configuration |
