cisco default console password
How do I set a password for my Cisco switch?
The first time that you log in to your switch through the console, you have to use the default username and password, which is cisco. You are then prompted to enter and configure a new password for the Cisco account. Password complexity is enabled by default.
How do I configure a Cisco router?
You may also initially configure your router by using the Cisco IOS command-line interface (CLI) or by using the setup command facility. To create the initial configuration, the setup command facility prompts you for basic information about your router and network. Note Some SKUs may not include a default configuration file.
What is a username & password in Cisco IOS CLI?
The username and password are the username and password that you determine. To continue using the Cisco IOS CLI for initial configuration, see the applicable configuration procedures in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Software Configuration Guide.
What is the default password for a Cisco router?
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168.1.1 or 192.168.1.254. However, some differ, as shown in the table below. Below is an updated list of default usernames, passwords, and IP addresses that I've obtained from user manuals and Cisco support pages.
Cisco Console Password
How to Configure Password on CISCO Router
How to set a Console Password on a CISCO Router Or Switch How to secure the console port
|
Replacing or Recovering a Lost Password
This chapter describes how to recover a lost enable or console login password and how to replace a lost enable secret password on your Cisco 4000 Series |
|
Catalyst 2960-S Switch Getting Started Guide (English)
13 (Optional3) Console cable or USB cable You must change the password from the default password cisco. Optional Fields. |
|
Cisco Small Business 300 Series Managed Switches Quick Start
you are managing the switch through a console port connection the link is retained. Default password is cisco (passwords are case sensitive). |
|
Cisco 350 Series Managed Switches Quick Start Guide Firmware
Console cable for using the console port to manage your switch. first time. Parameter. Default Value. Username cisco. Password cisco. |
|
Configuring Global Credentials for Access Points
log onto the console port of the access point. If you need to return the access points to the default. Cisco/Cisco username and password you must clear the |
|
Cisco 220 Series Smart Switches Quick Start Guide
Console cable for using the console port to manage your switch. first time. Parameter. Default Value. Username cisco. Password cisco. |
|
Smart Software Manager On-Prem Console Reference Guide - Cisco
13 nov. 2020 to change your password for the admin onprem console. NOTE: CiscoAdmin!2345 is default admin console password. |
|
Administrator Password Recovery for Cisco Business 350 Series
Press 3 to select option [3] Password Recovery Procedure. This will reset the password to null. Power cycle with the console cable and Putty connected. If the |
|
Remote Expert Mobile-Reset Web Gateway Admin Password
Following Article provides information on the process to reset Web Gateway Admin Password Contributed by Rajender Kalavala Cisco TAC Engineer. |
|
Configuring Local Authentication - Cisco
Router(config-if)# aaa authentication login default local line password configured for the console, the console line password serves as the enable password |
|
Controlling Switch Access with Passwords and Privilege - Cisco
This table shows the default password and privilege level configuration key passwords, the privileged command password, and console and virtual terminal |
|
Catalyst 2960-S Switch Getting Started Guide (English) - Cisco
and press Enter When prompted, enter the default password, cisco |
|
Controlling Switch Access with Passwords and Privilege - Cisco
for administrator login to the console, Telnet, SSH, webUI, and NETCONF must be This table shows the default password and privilege level configuration |
|
Catalyst 3850 Switches - Cisco
Terminal Lines are Used for Local and Remote CLI Sessions 10 Protect Access Username passwords using the default method for configuring the password |
|
Recovering a Lost Enable Password - Cisco
Note You can recover a lost enable password, but not a password that you configured with the enable secret Connect an ASCII terminal or a PC running a terminal emulation program to the Break disabled (default setting)—bit 8 is set to 1 |
|
Console Port, Telnet, SSH Handling, and Reset Button - Cisco
In Cisco IOS XE Gibraltar 16 12 releases and earlier, you can enable the Reset button feature only if you use service password-recovery configuration However, to |
|
Configuring Security with Passwords, Privileges, and Logins - Cisco
The following password types are stored as plain text in the configuration by default: • Console passwords for local CLI sessions • Virtual terminal line passwords |
|
User Security Configuration Guide, Cisco IOS XE Gibraltar 1611x
Configuring Security with Passwords, Privileges, and Logins 11 to Console, Telnet, SSH, webUI, and NETCONF, must be migrated to password type 8 or type 9 The default configuration of a Cisco IOS XE software based networking |
|
Catalyst 9200 Switches - Cisco
29 mar 2019 · Default Password and Privilege Level Configuration 3 key passwords, the privileged command password, and console and virtual terminal |
