cisco sonet switch
Cisco ONS 15454 SONET/SDH Multiservice Provisioning Platform
The Cisco ONS 15454 is the first in its class to consolidate SONET/SDH dense WDM (DWDM) transmission Layer 2 and Layer 3 packet-processing functions and storage area network (SAN) transport with the intelligence of an IP-based management plane in a single cost-effective platform |
Chapter 12 SONET Topologies and Upgrades
This chapter explains Cisco ONS 15454 SONET topologies and upgrades To provision topologies refer to the Cisco ONS 15454 Procedure Guide Chapter topics include: • 12 1 SONET Rings and TCC2/TCC2P Cards page 12-1 † 12 2 Bidirectional Line Switched Rings page 12-2 † 12 3 Path Protection page 12-13 † 12 4 Dual-Ring Interconnect page |
SONET Topologies
Figure 11-1 Four-Node Two-Fiber BLSR Node 3 Node 0 OC-48 Ring STSs 1-24 (working) STSs 25-48 (protect) STSs 1-24 (working) STSs 25-48 (protect) Node 1 = Fiber 1 Node 2 = Fiber 2 The SONET K1 K2 and K3 bytes carry the information that governs BLSR protection switches |
What is SONET & SDH?
SONET and SDH provide carrier-class circuit protection with sub-50-millisecond (ms) restoration and multilayer performance-monitoring statistics, enabling proactive maintenance and reduced communication downtime. Integration of the Cisco ONS 15454 into today’s network is simplified because of the adherence to telecom industry standards.
What is SONET line redundancy?
The implementation of the above protection schemes allows a pair of SONET lines or paths to be configured for line or path redundancy. In the event of a fiber cut, the active line or path switches automatically to the standby line or path in up to 60 milliseconds (2/5/10 millisecond for holdover and 50 millisecond switchovers).
What are SONET protection schemes?
The SONET protection schemes partially comply with Telcordia—GR-253-CORE standard. It allows Optical Interface Module to work seamlessly as SONET Add or Drop Multiplexers (ADMs). The implementation of the above protection schemes allows a pair of SONET lines or paths to be configured for line or path redundancy.
SONET Controller Commands - Cisco CRS Router
The configuration of the SONET controller includes SONET Automatic Protection Switch (APS) which is a feature offering recovery from fiber (external) or |
Mesure du niveau optique à travers IOS
Conventions relatives aux conseils techniques Cisco. Mesurer le niveau optique. Seules les cartes de ligne GSR (Gigabit Switch Router) 4 1xOC192 et 4xOC48 |
Chapter 20 RLS Commands
Cisco ONS SONET TL1 Command Guide R10.x.x. 78-21403-02 RLS-EXT-CONT cannot change the contact state to Automatic if the existing state is Manual Open. |
Automatic Protection Switching Configuration
Automatic protection switching (APS) is a protection mechanism for SONET networks that enables SONET connections to switch to another SONET circuit when a |
SONET Controller Commands on the Cisco IOS XR Software
The configuration of the SONET controller includes SONET Automatic Protection Switch (APS) which is a feature offering recovery from fiber (external) or |
Chapter 24 SW Commands
Cisco ONS SONET TL1 Command Guide Release 8.5.1. 78-18469-01. 24. SW Commands. This chapter provides switch (SW) commands for Cisco ONS 15454 |
Chapter 16 OPR Commands
Cisco ONS SONET TL1 Command Guide Release 8.5.1 RLS-EXT-CONT cannot change the state to automatic if the existing state is Manual Open. Caution. |
Chapter 13 EX Commands
This chapter provides exercise (EX) commands for Cisco ONS 15454 Cisco Exercise switch for the SONET protection line is not supported in this release. |
Chapter 13 EX Commands
Cisco ONS SONET TL1 Command Guide Release 8.5.1. 78-18469-01 Exercise switch for the SONET protection line is not supported in this release. |
Chapter 18 OPR Commands
Cisco ONS SONET TL1 Command Guide R10.x.x. 78-21403-02 RLS-EXT-CONT cannot change the state to automatic if the existing state is Manual Open. Caution. |
Configuring SONET - Cisco
3 receives the K2 byte and knows about switching event on device 2 1-Port OC- 192 or 8-Port Low Rate CEM Interface Module Configuration Guide, Cisco IOS XE |
Configuring OC3 Ports - Cisco
Cisco ME 3800X and ME 3600X and ME 3600X-24CX Switch Software Configuration Guide Chapter 3 Configuring OC3 Ports Configuring SDH and SONET |
Cisco SONET MIB Objects
APS has the ability to configure a pair of SONET lines for redundancy When the active line fails, the hardware will automatically switch the active line from the |
SONET Controller Commands on the Cisco IOS XR Software
To manually switch an automatic protection switching (APS) channel, use the aps group command in EXEC configuration mode aps group number {force manual} |
Chapter 13, Ethernet Operation - Cisco
SONET/SDH equipment protection switches) • Hitless reprovisioning • Support of Gigabit Ethernet traffic at full line rate • Full TL1-based provisioning capability |
Configuring the OC-12 ATM Optical Services Modules - Cisco
SONET and SDH Configuration Commands, page 8-31 ATM Overview Asynchronous Transfer Mode (ATM) uses cell-switching and multiplexing technology |
Cisco Network Convergence System 4000 Series
encapsulation ○ OTN switching: OTN switching includes full optical channel data unit level 0 (ODU-0) switching with ports supporting SONET/SDH, Ethernet, |
Cisco ME-3600X-24CX Series Switch Chassis Configuration Guide
MPLS-TP tunnels help transition from SONET/SDH TDM technologies to packet switching to support services with high bandwidth utilization and lower cost |
Hardware Support for Automatic Protection Switching (APS - Cisco
2 mai 2008 · Equipment (LTE), in this case a Cisco router or switch port SONET APS specifies use of the K1 and K2 bytes in the SONET and Synchronous |
Cisco SFP Optics for Packet-Over-Sonet/SDH and ATM Applications
The Cisco industry-standard Small Form-Factor Pluggable Interface Converter ( SFP) for packet-over-SONET/SDH (POS), optical networking, and ATM |