how to open port 12489 in windows
Configuring The Windows Agent NSClient++ for Nagios XI
understand how the configuration file works for NSClient++ to enable some of the TCP port 12489 for NSClientServer (Nagios XI Server check_nt > Windows ... |
Nagios XI Ports and Protocols
SSL is not turned on out of the box. SNMP ports 161 and 162. SNMP is an integral part of network monitoring. Nagios XI will send requests to nodes on port. |
Nagios Start Up Guide
12-Jan-2008 In addition instruction on the monitoring of Linux and Windows ... In the Windows firewall open two ports |
AT12489: Getting Started with Atmel ATtiny102 and ATtiny104
– Configure the PUEx register to enable internal pull-up of the corresponding port pin. Atmel AT12489: Getting Started with Atmel ATtiny102 and ATtiny104 [ |
Nagios Certified Professional
Windows is a registered trademark of Microsoft Inc. All other brand names In the Windows firewall open two ports 5666 for NRPE and 12489 for NSClient++ ... |
Nagios Core Documentation
Nagios® Core™ is an Open Source system and network monitoring application. the 'port' option in the [NSClient] section is uncommented and set to '12489' ... |
Using Nagios Core for Monitoring in Dynamic Data Masking
Configuring Nagios Core for Dynamic Data Masking on Windows. The port must be open on the local firewall. 1. Run the following commands to download the ... |
Ports.pdf
Port TCP UDP. Description. Status. 42. TCP UDP. ARPA Host Name Server Protocol. Official. 42. TCP UDP. Windows Internet Name Service. Unofficial. |
Nagios Certified Administrator
Windows is a registered trademark of Microsoft Inc. All other brand names These public services allow Nagios to not only check to see if the port is ... |
Table of Contents
03-Feb-2018 If you use the NSClientListener (check_nt) you need the (modified) NSClient port open (usually. 12489) from the nagios server towards the ... |
Port 12489 Connection refused issue - Nagios Support Forum
2 août 2021 · I'm using NCPA to monitor a Windows machine with NRDP (passive check) and quite sure there's no port blocking issue as Windows firewall is |
Configuring The Windows Agent NSClient++ for Nagios XI
PORT NUMBER - Port to use for check_nt port = 12489 • The lines enclosed by [square brackets] are the different sections in the configuration file |
Port 12489 (tcp/udp) - SpeedGuide
This can be accomplished in both Windows command prompt and Linux variants using the "netstat -aon" command We also recommend runnig multiple anti-virus/anti- |
Nagios 12489 connection refused - Let us fix it - Bobcares
24 avr 2020 · Nagios 12489 connection refused error can be rectified by opening port 12489 enabling check_nt command enabling NSClient modules etc |
Nagios error port 12489 connection refused
Make sure that port is open on your windows firewall as well as any other -The-Windows-Agent-NSClient++-for-Nagios-XI pdf What is port 12489 in Nagios |
Configuring The Windows Agent NSClient++ For Nagios XI PDF
Make sure all ports that need to be open can be access from the Nagios server (port 12489 for NSClient++ port 5666 for NRPE and port 5667 for NSCA) |
Monitoring Windows devices via NSClient++
Make sure the “port” option in the [NSClient] section is uncommented and set to '12489' (the default port) Start the NSClient++ service with the following |
Nscp-docs/installingmd at master - GitHub
If you use the NSClientServer (check_nt NSClientListener) you need the (modified) NSClient port open (usually 12489) from the Nagios server towards the |
(PDF) NSClient++ Reference Manualpdf - DOKUMENTIPS
server towards the client 12489) from the nagios server towards the client All these ports can be changed so check your nsc ini process so hopefully |
What is port 12489?
12489 is typically the NSClient++ default port. NCPA listens on 5693 by default.2 août 2021How to configure NSClient ++ on Windows?
Installing The Agent
1Select Generic and click Next to continue.2Click the Typical button.3In the next step you will need to configure the NSClient++ agent. 4Enable common check plugins = Checked. 5Click Next to continue. 6Wait while NSClient++ is installed and click Finish to complete the setup.What is port 12489 in Nagios relevant for?
NSClient program is a simple monitoring daemon, that is used to collect, receive, and distribute data metrics to Nagios monitoring tool. The default port used by check_nt and NSClient is port 12489.24 avr. 2020- Right click the NSClient++ service and select Restart. You can close the Services console as it's no longer required.
Configuring The Windows Agent NSClient++ for Nagios XI
Establish a terminal session to your Nagios XI server as root and run the following command: nmap -p T:12489 The screenshots on the following page show the nmap command and output If it shows an open state (left image) then NSClient++ is listening on that port and it is open |
Configuration de Nagios
Configuration de Nagios pour surveiller vos machines Windows Ce genre de question revient régulièrement quand on doit faire le choix entre une solution open- il faut peut être vérifier que la requête (TCP sur port 12489) n'est pas |
Mise en place dun système de supervision Open source - UVT e-doc
Open source NSClient pour la supervision des serveurs Windows →Vérifier que les requêtes (TCP sur port 12489) ne sont pas bloquées par un firewall |
Nagios 331 for IPBRICK Guide
21 août 2012 · 4 1 3 Other machines or Windows Servers When testing, disable the windows firewall or enable port 12489 used by the NSClient |
Nagios XI Windowsエージェントの設定 - ジュピターテクノロジー
25 nov 2016 · 前に、監視対象の Windows マシンに NSClient++エージェントが NSClientServer: port 12489 (Nagios XI サーバー check_nt > Windows マシン) open ステータスの場合、NSClient++はこのポートでリスンしています: |
Table of Contents - Doku-Wiki
Table of Contents Dependencies for Windows NT4 If you use NRPEListener ( check_nrpe) you need the NRPE port open (usually 5666) from the nagios 12489 The nagios server initiates a call to the client on port 12489 NSCA client |
SUPERVISION RESEAU AVEC NAGIOS RAPPORT - cloudfrontnet
De plus, Nagios est un outil Open source: Chaque société peut l'adapter comme elle lui semble Puis, la D'un serveur "Windows Server 2003" qui permettra la gestion des utilisateurs du réseau : Stockage des port=12489 ; ;# BIND TO |
Installation de nagios - WordPresscom
service nagios reload/ start /restart et ouvrer aussi pouvoir superviser un serveur Linux ou Windows -p : mettre le port de nsclient++ port par défaut 12489 |
Nagios Documentation - Network Startup Resource Center
Without installing an agent on the Windows box, Nagios would be set to '12489 ' (the default port) 8 Start the NSClient++ service with the following command: |
Nagios Start Up Guide - cxcorenet
In the Windows firewall open two ports, 5666 for NRPE and 12489 for NSClient ++ ааBoth are TCP ports ааYou can see in the example how it should look when |