2) Assemble mounting screws into threaded holes in mounting strap 3) Attach INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET
USESI installation instructions
InstallatIon: 1 At the desired fixture location, mount the receptacle box If wall mounting, the box must be mounted vertically 2 For optimum light output when
is cb
4) Connect safety cable assembled to canopy to mounting strap (This will allow INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/OR IN WET
is cb
19 mai 2015 · ASSEMBLY AND INSTALLATION INSTRUCTIONS for the 4233/4234/4236 Fixture 1 Remove the fixture, parts and all mounting hardware
install
5) Push fixture to wall, carefully passing mounting screws through holes 6) Secure fixture to wall Pour L'assemblage et L'installation Au Canada MOUNTING
d a bb a b b c a
All HID Fixtures: Remove (4) cage screws, and lift fixture/ballast assembly up and out of housing Connect conduit to fixture using following instructions
instruction sheet
For enclosed MR16 style fixtures, first remove the baffle assembly or front lens assembly, pulling slowly while grasping the leading edge Insert the lamp plug into
LV FIXTURE INSTALLATION
These fixtures are intended to be installed utilizing NEC compliant junction This instruction shows a typical installation 1 2 Feed the fixture wires through the collar nut, canopy and half ball assembly, then screw it onto the stem assembly
InstructionSheets?brand=Feiss&filepath=EC
systems (provided with Ground wire or equivalent protection system) • For your safety, it is strongly recommended that two people install the lighting fixture • This
Ellis Square Crystal Chandelier Assembly Instructions
1) Screw center stem onto threaded pipe on top of fixture body. 2) TURN OFF POWER. IMPORTANT: Before you start NEVER attempt any work without.
1) Screw center column onto coupling at top of fixture body. 2) Turn oFF Power. IMPORTANT: Before you start neVer attempt any work without.
13) Placer le cache au plafond. 14) Fixer le cache en serrant la bague filetée sur le collierécrou. 15) Visser l'extrémité tube fileté avec le talon l déjà
1) Turn off power. IMPORTANT: Before you start neVer attempt any work without shutting off the electricity until the work is done. a) Go to the main fuse
1) Turn off power. 2) Slip fixture over post and mark position of mounting holes in post. 3) Remove fixture from post. 4) Drill 3/16” dia holes in post at
10) Assemble stem to fixture -. 11) Note direction of exposed threaded pipe on illustration. Bottom two pipes will have exposed thread at top.
If the fixture to be replaced has a switch or pull chain place those in the “off” position. 2) find the appropriate threaded holes on mounting strap. Assemble.
1) Pass wire from fixture though stem and screw stem to top of fixture. NOTE: Thread locking compound must be applied to all stem threads.
1) Screw center stem to top of fixture body. 2) Pass wire through stem and screw stem to top of center stem. NOTE: Thread locking compound must be applied
11) Placer le cache au plafond. 12) Fixer le cache en serrant la bague filetée sur le collier-écrou. 13) Soulever l'abat-jour jusqu'au luminaire en passant
INSTALLATION INSTRUCTIONS Pass fixture wire from coupling[K] on top of main body through desired number of short threaded tubes[A] and stems[B] Screw stems together using short threaded tubes Thread assembled stems into coupling[K] on top of main body
Assemble fixture as shown in illustration above Be sure to run wire leads through slot in stake Lay the fixtures out where you want to locate them The first fixture should be at least 10 wire feet from the power pack WARNING-RISK OF ELECTRICAL SHOCK: Do not place a xture within 10 feet of a poolor spa
Nov 18 2011 · This instruction sheet covers the installation of the following Kichler® Transformers: 15PR100SS 15PR200SS 15PR300SS 15PR600SS 15PR900SS Read these instructions carefully before installing this unit This power supply is for use with landscape lighting systems only
iNSTAllATiON iNSTrUcTiONS P/N: 12353BK 12353Wh NOTe: All installations should comply with national and local electrical codes if you have any doubts concerning installation contact a qualified licensed electrician iMPOrTANT SAFeTY iNSTrUcTiONS A) Read all instructions B) Do not conceal or extend exposed conductors through a building wall
INSTRUCTIONS For Assembling and Installing Fixtures in Canada Pour L assemblage et L installation Au Canada 1) Pass fixture wire and ground wire thru desired amount of stems D & E and thread together using supplied nipples NOTE: Use a drop of Thread compound (supplied) on the threads 2)ead Swivel onto stems securely Pass threaded Swivel Thr
INSTRUCTIONS For Assembling and Installing Fixtures in Canada Pour L’assemblage et L’installation Au Canada QUIC DISC™ WIRING INSTRUCTIONS Turn off power The full length of the 18 GA fixture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:
How to install a light fixture?
1. Pass the main wire through the waterproof rubber gasket which also protect the lamp from seeping-water. 2. Connect L/GND/N wire to corresponding holes, then tighten the screws nearby. 3. Install the back plate where you want it to be. 4. Joint the light fixture, then fasten the middle screw firmly, and installation is over.
How do I install the MA fixture builder?
Download the latest version from www.ma-dot2.com or www.malighting.com. The installation is possible in every root directory or in the standard directory "MA Lighting TechnologiesMA Fixture Builder" in the folder "Program Files". You should have administration rights to install the program.
How do I address a fixture?
To address a fixture: 1. Tap the fixture in the list and look at the Start address number 2. Use the digital display on the actual fixture to set the same number. Refer to the fixture manufacturers manual on how to do this. Some fixtures use DIP switches instead of a digital display.
How do you install wall-mounting fixtures?
Install back-outlet, wall-mounting fixtures onto waste fitting seals and attach to supports. Install floor-mounting fixtures on closet flanges or other attachments to piping or building substrate. Now install wall-mounting fixtures with tubular waste piping attached to supports.
INSTRUCTIONS For Assembling and Installing Fixtures in Canada