[PDF]
INSTALLATION INSTRUCTION 217 - LED Wall Sconce WS-21718
- Read all instructions before installing - System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations - Go to the main fuse box, or circuit breaker Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
[PDF]
Installation Instructions B247 - SHOP Hubbardton Forge
Installation Instructions B247 Banded Sconce 20-5812, 20-5812F & 20-5892, 20-5892F Page 1 of 1 Hand-Forged, Vermont-Made Lighting and Accessories 154 Route 30 South, Castleton, Vermont 05735 26953 Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all applications If
[PDF]
TE-Series PRO Channels Sconce Installation Instructions
IS-TE-Series PRO Channels Sconce Installation-CB TE-Series PRO Channels Sconce Installation Instructions MODEL: 1TEC2S1SF8SIL MODEL: 1TEC4S2SF8SIL 6) Fasten end caps with provided screws Two screws will engage the mounting extrusion on each end cap Please see next page for CAUTIONS, WARNINGS, and FCC Information INSTALLATION: 1) Prep electrical feed as
[PDF]
LED Product Information and Warnings
Assembly Instructions INSTRUCTIONS D’INSTALLATION Band Series - 8" LED Sconce, 13" LED Sconce, 21" LED Sconce Important • Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance • Consult a qualified, licensed electrician to ensure correct branch circuit conductor
[PDF]
CAUTION NOTICE - HVL Group
225-11 vertigo wall sconce gold finish installation instructions warning disconnect power before re-lamping or wiring the fixture read all instructions completely before starting installation caution •to avoid the risk of fire or shock, fixture must be installed in compliance with all applicable national and local electrical/building codes
[PDF]
1 2
Band light fixture by removing 4 flat head screws Slide the canopy cover onto the crossbar assembly threaded pipe Then place gasket washer over the crossbar assembly threaded pipe Next slide back plate onto the crossbar assembly, place second gasket washer, external tooth locking washer, nut, and securely tighten Ensure canopy cover and back plate are positioned level
Band wall sconce - Installation Instructions Model BA- 1 Product must be installed in accordance with the applicable installation code by a person familiar with
band install
Adagio An array of geometric patterns in Adagio two-light wall sconce is a nod to the musical features lights that are distributed around a circular Black band
PROG P spec
from minimum lighting and continues the regulation until the button is released If the device is installed individually, follow the instructions indicated in Figure 1 Figure 1: Once the blue LED remains permanently ON, you may play music
B ELSB Cat Light switches and socket outlets LR
NOTE: An optional wall support mounting bracket is available to aid in securing SAFETY WARNING: Luminaire can become very hot depending on lamp wattage with #10 screws provided (side bands of JBCP-150 may be bent outward to
Inst
designs A large selection of light fixtures and light kits are also available INSTALLING THE WALL TRANSMITTER housing over the motor center band
F English
Form a loop in the cable where the lights will be located (with a rubber band if desired) to leave enough slack for connection of the light to the power cable 7
d bc b d b fb d
LED Wall Sconce Fixture Read all safety precautions and installation instructions carefully It is recommended that a qualified electrician perform all wiring the diffuser (2), align diffuser above frame (1), Slide diffuser behind trim bands
Instructions TRS BRS LED R
Connect the existing wires in the wall box to the sensor flying leads (See Wiring Directions at right) • Do not allow bare wire to show below connector • The
WS instruction manual
This guide provides the best practice guidelines for installing the HardieZone product for your zone Air Conditioners, Service Panels and Other Wall Mounted Devices 21 and corner details, HardieTrim 5/4, 4/4 boards may be used to construct light (Figure 8 10) Terminate ends of the Band Board into Trim or Siding
Best Practice Guide HZ US English
ICOM-CC Leather and Related Materials Working Group. 11 ème. Réunion intermédiaire du Groupe de DIM Matériaux anciens et patrimoniaux - Ile de France.
ICOM-CC Leather and Related Materials Working Group. 11 ème. Réunion intermédiaire du Groupe de DIM Matériaux anciens et patrimoniaux - Ile de France.
The International Union for Conservation of Nature and Natural Re- which evolution of a group of species can go to exploit valuable food sources.
37 Venice Commission CDL-AD(2010)024
ICOMOS SDGs Working Group Task Team for Priority Action 1. Previously Linda was the Academic and Research Coordinator for Architectural Conservation
and instructions specified in the M.A.401 maintenance data. o Incident of aircraft Airbus A340 registration FGTUB
Dec 9 2004 the wonderful dinners and lunches of previous reunions and was ready to ... and help received from Guy Girod
Nov 29 2012 uniforms with KLA patches and were armed with “pistols
Our Getting Started Guide gives you an overview of the Pearson Edexcel International. GCSE in French to help you understand the changes to content and