Installationsanleitung T8 LED-Tubes mit Starterüberbrücker. 1. Allgemeines. Vor Installation der LED-Tubes ist die derzeitige Anschlussvariante der Leuchten
Installationsanleitung T8 LED-Tubes mit Starterüberbrücker 1 Allgemeines Vor Installation der LED-Tubes ist die derzeitige Anschlussvariante der Leuchten zu überprüfen Hierzu sind die Hinweise in 2 Vorbereitung der Installation zu beachten Die Installation von LED-Tubes darf nur im spannungsfreien Zustand und nur von
to install the LED T8 tube please read the entire installation guide carefully Ensure that package includes: installation guide warning label to be attached to luminaire LED T8 tube and LED dummy starter Product is not intended to be used with dimmers and emergency light luminaires
Dec 17 2020 · Table #1 – T8 LED Tube – Type A or Type A/B Hybrid - Page 1 of 2 IMPORTANT NOTICE: This list is based on testing performed using a stable AC power supply under laboratory conditions which may not be represen tative of particular end-use conditions
T8 12T8/COR/48-840/MF18/G 10/1 Philips MainsFit (UL Type B) CorePro T8 LED tubes deliver high-quality flicker free performance at an affordable price The UL Type B LED tubes are designed with easy installation and long-term maintenance simplicity in mind Upgrade your lighting to Philips and realize 50000 hour LED lifetime backed by a 5-year
1: Switch off the electricity supply 2: Remove the conventional lamp 3: Remove the starter 4: Stick the warning label in a visible location 5: Click the LED replacement starter into the starter holder 6: Insert the LED Tube into the lampholder 7: Secure the position by turing the lamp by 90° 8: Switch on electricity and check for
T8 LED Tube Installation Instructions 1 Turn off power 2 Remove old Fluorescent tubes 3 Access the ballast by removing ballast cover 4 Disconnect and cut wires feeding to the ballast input (live and neutral wires) they should remain as long as possible 5
installation instructions led lamp luminaire marking labels the t8 led tubes are intended to retrofit listed surface mounted type non-ic or type ic recessed mounted fluorescent luminaires with or without diffuser for maximum four lamps with lamp to lamp distance 11 cm minimum; or retrofit surface mounted listed fluorescent luminaires
1 Coupez l’électricité 2 Retirez la lampe ?uorescente existante 3 Retirez le démarreur ?uorescent existant 4 Insérez le démarreur T8 LED 5 Insérez le tube LED 6 Branchez l’alimentation de V-TAC LED Démarreur LED Ballast inductif AC:220-240V 50Hz AC:220-240V 50Hz LA GAUCHE LA GAUCHE DROITE DROITE (L) (N) V-TAC ENTRÉE V-TAC
The T8 LED tube must not be installed in rainy wet dusty and combustible environment Please confirm whether the light fixture meets the protection requirements 2 Installation Requirements The installation job should be done by electrician or experienced people The operating temperature is -20??+40? 3 Dimension 589mm
Installationsmöglichkeiten 1 2 Umrüstung einer KVG-Leuchte gemäß EN 62776 Ersetzen der T8-Leuchtstofflampe und des eingebauten Starters durch SubstiTUBE®T8 EM und SubstiTUBE®Start Alternativ kann auch die SubstiTUBE®T8 Universal und SubstiTUBE®UN-Start für KVG-Leuchten verwendet werden 1 3 Direktverdrahtung einer EVG oder KVG-Leuchte
How do I install a T8 LED Luminaire?
- Insert T8 LED lamp Turn power back on and check for proper operation Turn power off by disconnecting the supply voltage Remove current fluorescent lamps and starters. Dispose of them properly based on local regulations. Wire luminaire to the configuration shown on drawing 3.
What is a T8 tube?
- LED T8 Tubes LED T8 Tubes of equivalent dimensions are suitable to replace 16/18W 2ft, 32/36W 4ft or 51/58W 5ft fluorescent T8 lamps in luminaires containing standard non-shunted G13 (medium bi-pin) lamp holders. For use on electronic gear please refer to direct wiring/new luminarie section of the instructions.
How do you replace a fluorescent starter with a GE LED T8?
- Only use the replacement GE LED T8 lamp type or contact manufacturer for more information.” Turn power off by disconnecting the supply voltage Remove current fluorescent lamps and dispose of them properly based on local regulations Find and remove existing fluorescent starter Insert LED T8 starter provided into existing fluorescent starter location
What is the address of T8 LED tube?
- Address : No.7, Fengxiang Road, Wujin Hi-tech Industrial Zone, Changzhou, Jiangsu Province, China Postcode : 213100 Tel : +86-519-69690163 Fax?025-68516914 T8 LED Tube Manual Title TB003?????-UL