the purchase of a new pump don’t overlook the most important item - the baseplate Without a solid, easy to install, corrosion resistant baseplate you increase the risk of problems on site as well as increase your overall costs Goulds ChemBase PlusTM baseplates are made from state of the art polymers, which offer exceptional flatness,
Polyshield® Baseplates are filled with regular 3000psi concrete fill which is less expensive than epoxy grouts • Preparation Metal baseplates must be sandblasted for grout adhesion Polyshield does not • Installation No concrete forms, no grout air pockets and no long cure times as with metal baseplates • Maintenance
Before we consider the technical properties and the installation of grouts we need to be mindful of the particular project we are working on It is important to ensure we don’t under specify a product but also allow for the use of lesser performing products in less critical applications to provide a more cost effective installation
1 Base Plate and Anchor Rod Design JAMES M FISHER, Ph D , P E Computerized Structural Design, S C Milwaukee, Wisconsin and LAWRENCE A KLOIBER, P E
of the pump Failure or neglect to properly install, operate, or maintain the pump may result in personal injury, property damage, or unnecessary damage to the pump Variations exist in the equipment used with the pumps and in particular installation of the pump and driver Therefore, specific operating instructions are not within the scope of this
when the pump is started This will reduce the start-up load on the pump and motor Never start the pump with the discharge valve closed Inlet valving should be open when starting any pumping system Without some fluid in the pump, it can gall and lock up impellers Always fill the pump and vent it of air for best pump life Violent pump
1 Base Plate and Anchor Rod Design JAMES M FISHER, Ph D , P E Computerized Structural Design, S C Milwaukee, Wisconsin and LAWRENCE A KLOIBER, P E
MIXING: A paddle type mortar mixer, grout pump, or heavy duty 1/2” drill with mixing prop are required Place approximately 80 of required water into clean pre-wet mixer or container Use only as much water as needed to properly place the grout Adding excess water decreases strength and expansion For Ohio Department of
MIXING: A paddle type mortar mixer, grout pump, or heavy duty 1/2” drill with mixing prop are required Place approximately 80 of required water into clean pre-wet mixer or container Use only as much water as needed to properly place the grout Adding excess water decreases strength and expansion When using aggregate add it to the water
its plastic state For large area pours consider using a grout pump 8 Finishing Grout constructive solutions
Pregrouted Base Plate System, and a new installation technique, the Stay-Tru™ Field one-thousandth of an inch deep the desired monolithic support system has not been PROCEEDINGS OF THE 19TH INTERNATIONAL PUMP USERS SYMPOSIUM 132 anchor bolts The 100 ft-lb of torque was considered to be
Prefilled Equipment Baseplates How to get a Superior Equipment Installations for less Money
polymer concrete foundation systems, and pregrouted conventional metallic Improvement of installation techniques included improved grout placement ask if grouting pump baseplates with epoxy is cost effective? The the new brand's service representative In order to consider wider application of vertical pumps
elimination of anchor bolts, separate base plates, and grouting systems, the time and Non-Grouted Pre-Grouted in the range of 0 10 inches/second are considered desirable by new designs may go a long way toward eclipsing conventional pump support systems in refining and petrochemical traditional method
Polyshield Paper
installation and precommissioning of new, existing, and reapplied machinery and to assist general-purpose gears, API 674 reciprocating pumps, API 676 rotary positive turbine in the train should be considered to be special-purpose sometimes be mounted on spring-supported baseplates to reduce nozzle loading
reie c da a f edff ddc a
please call Chockfast Grouting Systems Customer Service at is a good practice to discuss your particular application with your local ITW FOR EPOXY GROUTING OF PUMP BASEPLATES, RAILS, OR SOLEPLATES 8/1/91 AVOIDED WHEN USING THE PRE-GROUTED OR INVERTED TECHNIQUE BECAUSE OF
chockfast machinery grouting manual industrial ebc
SUPPORTING ROTATING MACHINERY A pregrouted base plate and the method of its use and construction With rotating machinery such as pump and
US
Pregrouted Base Plate System and a new installation technique
polymer concrete foundation systems and pregrouted conventional metallic baseplates. Reliability and vibration data for each installa-.
from new construction materials methods
herein only because they are considered essential to the objective of rock-excavation support known as the “New Austrian Tunneling Method” (Rabcewicz.
01-08-1991 CHOCKFAST BLUE oil-resistant foundation cap/grout for new installations; ... FOR EPOXY GROUTING OF PUMP BASEPLATES RAILS
and support our clients during installation fixed to the rock using this technique. ... completely new requirements for stability.
Polyshield® precast polymer concrete foundation systems consist of a foundation baseplate shell for rotating pumps and motors (Figure 1). The.
Polyshield® precast polymer concrete foundation systems consist of a foundation baseplate shell for rotating pumps and motors (Figure 1). The.
dations machinery support systems
PREFILLED EQUIPMENT BASEPLATES— HOW TO GET A