[PDF]
INSTALLATION basicDIM DGC - Tridonic
[PDF]
Lighting Controls and Connectivity basicDIM basicDIM DGC
If the basicDIM DGC module is used in the basic application, the CH2 can be used as control channel for controlling subordinate basicDIM DGC modules (basic connection), so that the controlling and the subordinate basicDIM DGC modules can be programmed and allocated to groups using the masterCONFIGURATOR software Every single basicDIM DGC module can be allocated to a group
[PDF]
luxCONTROL lighting control system basicDIM basicDIM DGC
Installation • basicDIM DGC can be operated without sensor The motion detection must be disabled via masterCONFIGURATOR or with unique connecting a sensor and • basicDIM DGC Programmer • DSI/DALI is not SELV The installation instructions for mains •voltage therefore apply • The maximum cable length between the external switch and
[PDF]
luxCONTROL DALI basicDIM DGC Product Manual
Installation basicDIM DGC can be operated without sensor For this, the motion sensor must be deactivated with the masterCONFIGURATOR software _ _ DSI/DALI is not SELV The installation instructions for mains voltage therefore apply _ The maximum cable length between the external switch and basicDIM DGC is 100 m
[PDF]
basicDIM basicDIM DGC Compact control module with 2
basicDIM DGC 28000920 Luminaire installation 10 pc(s) Technical data Rated supply voltage 220 – 240 V Mains frequency 50 / 60 Hz Power 2 5 W Output, stand-by 0 5 W Current draw, input (DALI bus) 2 mA Operating temperature 0 +60 °C Storage temperature ts -25 +70 °C Type of protection IP20 Max casing temperature tc 70 °C Approval marks Standards
[PDF]
Sensors and Controls basicDIM DGC At a glance
basicDIM DGC - At a Glance 02-2019 1 1 EN c 3 / 9 1 What is the basicDIM DGC The basicDIM DGC, also named " ALI roup ontroller", allows you to set-up an easy to use, low cost constant light system withD G C motion detection If movement is detected by a sensor, an individually configurable motion detection profile will be triggered by the
[PDF]
28000920
basicDIM DGC 28000920 Luminaire installation 10 pc(s) Technical data Rated supply voltage 220 – 240 V Mains frequency 50 / 60 Hz Power 2 5 W Output, stand-by 0 5 W Current draw, input (DALI bus) 2 mA Operating temperature 0 +60 °C Storage temperature ts -25 +70 °C Type of protection IP20 Max casing temperature tc 70 °C Approval marks Standards
Sensor basicDIM DGC Sensor DA DA 2 3 4 6 7 DALI IN max 64 DGC max 500 W (L') max The installation instructions for mains voltage therefore apply
Inst basicDIM DGC
Manual basicDIM DGC 01-2021 1 12 en Table of Contents c 2 / 48 DSI/ DALI is not SELV The installation instructions for mains voltage therefore apply _
basicDIM DGC Manual en
Installation c Product manual basicDIM DGC 12-2014 1 3 en 11 51 I NOTICE Installation basicDIM DGC can be operated without sensor DSI/DALI is not
DALI basicDIM DGC ProductManual en
Mounting Packaging carton basicDIM DGC 28000920 Luminaire installation 10 pc(s) Specific technical data Type Inputs Outputs CH2 as Link Line Output
Fisa tehnica TRIDONIC basicDIM DGC
basicDIM DGC - At a Glance 02-2019 1 1 EN c 2 / 9 Table of ceiling installation basicDIM DGC Programmer REMOTE- CONTROL IR6 28000920
basicDIM DGC At a Glance en
Parameter settings basicDIM DGC PROGRAMMER 12-2018 en basicDIM DGC PROGRAMMER c 2 / 9 Dim up Increase current dimming level Dim down
basicDIM DGC PROGRAMMER en
L'appareil de commande de groupes basicDIM DGC de Tridonic comble la brèche existante entre la commande d'éclairage simple et les fonctionnalités DALI
PR LB basicDIM DGC FR
basicDIM DGC Installation Installed in luminaire Installed in luminaire/mounted on ceiling Daylight, presence, remote control Mounting height 5 m DSI/DALI
luxControl EN
Hauteur d'installation maxi 5 mètres Entrée d'un bouton Programmation par télécommande BASIC DIM DGC CELLULE BASIC DIM ILD 5DP CELLULE
CORRA DECO NC
Type. Article number Mounting. Packaging carton Weight per pc. basicDIM DGC. 28000920. Luminaire installation 10 pc(s). 0.06 kg. Specific technical data.
basicDIM DGC. 28000920. Luminaire installation 10 pc(s). Specific technical data. Type. Inputs. Outputs. CH2 as Link Line. Output relay (L'). Dimming.
DALI/DSI is not SELV. The installation instructions for mains voltage therefore apply. • basicDIM DGC can be operated without sensors. • Any number of push to
Offset Value -30 %. Set the difference in brightness between channel 2 and channel 1 to -30 % Page 5. Parameter settings basicDIM DGC PROGRAMMER
basicDIM DGC. Installation. Installed in luminaire. Installed in luminaire/mounted on ceiling. Daylight presence
basicDIM DGC Sensor 5DPI 14f black Luminaire installation 28001696. 40 pc(s). 0.06 kg. 1 The measured value at the sensor head corresponds to approx.
I NOTICE. Installation. basicDIM DGC can be operated without sensor. For this the motion sensor must be deactivated with the. masterCONFIGURATOR software.
Operating basicDIM ILD with other sensors c. 9 / 15. 2.1. Basic functions. Icon. Designation. DALI MSensor 02 /. MSensor 5DPI 14. basicDIM DGC SMART Sensor
Sensor Eingang für den Anschluss von bis zu 4 basicDIM DGC. Sensoren 5DPI 14 Leichte „click in“ Installation des Sensors.