André Martel 167 rang des Écossais St Césaire Québec JOL 1TO Canada Martel Small 1/4" 2" to 6" 43 Hook Medium 3/8" 4" to 12" 54 Dearest easy working tool
ANDRÉ MARTEL WWW CROCHETMARTEL COM 167 Rang des Ecossais WWW MARTELHOOKTOOL COM 3741/20 St V Parting Tool - Professio $86,99 F33 LONG THIN B E PARING CHISELS
Tools used for this project: Roughing gouge, 1/2" spindle gouge, 1/2" drill, André Martel turning hook tool, beading tool set, parting tool, 1/2" bedan, and sandpaper Blank turned round with a tenon on one end to fit the chuck I typically use a blank that can be roughed into a cylinder that is about 3" diameter and 8" long
Tools used for this project: Roughing gouge, 1/2" spindle gouge, 1/2" drill, André Martel turning hook tool, beading tool set, parting tool, 1/2" bedan, and sandpaper Blank turned round with a tenon on one end to fit the chuck I typically use a blank that can be roughed into a cylinder that is about 3" diameter and 8" long
professional turner from Montreal and André Martel, of the Martel Hook tool Brian McEvoy, a full time turner from Edmonton and a student of Frank Sudol’s some years ago, carries on Su-dol’s tradition of deep hollowing birch vases decorated with pyrography and piercing In his home studio, he has a two inch diameter bar, eleven feet long
such as the Martel Hook tool, the Munro tool, the spiralling and texturing tools and the thread chaser There are pin holes every 25 mm along the 300 mm width The pin gives you a perfect guide Stem Ø 30 mm, length 300 mm C ode DHA-G000-0300 Toolrests Length ranges from 150 to 500 mm Stem Ø 30 mm or Ø 40 mm Ø 30 mm Code 150 mm DHA-0000-0150
tool shaft differently than with a gouge Hook tool shapes tend to be individual and unique, so you will have to learn to use and sharpen each one per its own charac-teristics For example, the ones sold by André Martel and the ones sold by Mike Hosaluk are very different in shape and use And you can make your own too
A flexible decision support tool for maintenance float systems - a simulation approach 29 Francisco Peito, Guilherme Pereira, Armando Leitão, Luís Dias, José Oliveira From safety requirements to simulation-driven design of safe systems 40 Alfredo Garro, Andrea Tundis, Lena Buffoni-Rogovchenko, Peter Fritzson
[PDF]
André Martel 167 rang des Écossais St - Martel Hook Tool
[PDF]
André Martel - Martel Hook Tool
André Martel 167 rang des Écossais St Césaire Québec JOL 1TO Canada T/F: Martel Small 1/4" 2" to 6" 43 Hook Medium 3/8" 4" to 12" 54 Tools Large 1/2" 10"and up 65 Stress-proof Nickel-plated Set screw + Allan key SHANK # Ø L Hook Ø 1 1/2" 9" 1/4" 21
[PDF]
Turning a Goblet with Captive Rings - West Bay Woodturners
Using the tool of your choice to hollow the free end to form the interior of the goblet bowl In the picture I’m using an André Martel brand turner’s hook tool, but a gouge, termite tool, or any other end grain hollowing tool will work Form the exterior contour of the goblet bowl and the upper part of the stem next Sand the goblet bowl and apply finish if you are using a lathe applied
[PDF]
150TH CHAPTER OF THE AMERICAN ASSOCIATION OF
professional turner from Montreal and André Martel, of the Martel Hook tool Brian McEvoy, a full time turner from Edmonton and a student of Frank Sudol’s some years ago, carries on Su- dol’s tradition of deep hollowing birch vases decorated with pyrography and piercing In his home studio, he has a two inch diameter bar, eleven feet long Kurt Hertzog, who has demon-strated for us
[PDF]
LATHES - Classic Hand Tools
such as the Martel Hook tool, the Munro tool, the spiralling and texturing tools and the thread chaser There are pin holes every 25 mm along the 300 mm width The pin gives you a perfect guide Stem Ø 30 mm, length 300 mm C ode DHA-G000-0300 Toolrests Length ranges from 150 to 500 mm Stem Ø 30 mm or Ø 40 mm Ø 30 mm Code 150 mm DHA-0000-0150 200 mm DHA-0000-0200 300 mm DHA
[PDF]
Between Turns
on the tool handle will stop the tool from rolling off of the lathe bed or work table P A G E 3 Turning a goblet involves spindle turning and end grain hollowing Though the final project can be quite ornate, an attractive functional piece can be made by a beginner Tools used for this project: Roughing gouge, 1/2" spindle gouge, 1/2" drill, André Martel turning hook tool, beading tool set
[PDF]
wwwcapwoodturnersorg May 2019 C a p i t a l A r e a Wo o
Hook tool shapes tend to be individual and unique, so you will have to learn to use and sharpen each one per its own charac-teristics For example, the ones sold by André Martel and the ones sold by Mike Hosaluk are very different in shape and use And you can make your own too Steve Antonucci showed us that in his Dec 2012 demo Check out this Hook Tool Tutorial by Tod Raines at The
[PDF]
12th International Conference on Modeling and Applied
M H T PRICE LIST Can $ 2016 ORDER Ø Turning Ø Can $ Quantity Total Martel Small 1/4" 2" to 6" 47,5 Hook Medium 3/8" 4" to 12" 59,5 Tools Large
Can price list june
ANDRÉ MARTEL WWW CROCHETMARTEL COM 167 Rang des Ecossais WWW MARTELHOOKTOOL COM St-Césaire Québec J0L-1T0 T-F:450 293- 2186
Sablage finition varia