[PDF]
Viking Use & Care Manual
aluminum foil should be used in or around any part of the oven Improper oven liners may result in a risk of electric shock or fire Keep oven free from grease buildup G e t t i n g S t a r t e d Warnings 8 Cooking Safety (cont ) • ALWAYS place oven racks in the desired positions while oven is cool Taille du fichier : 1MB
Leave Installation Instructions with homeowner Homeowner: Keep than 1 inch, install Extended Dryer Feet Kit, Part water and plastic foil vent with rigid metal or flexible metal vent Use clamps to interior of the vent to secure vent into a hook 10 Insert tab of terminal block cover into slot of dryer rear panel Secure
installation instructions
metal (semi-rigid or foil-type) duct is installed, it must be UL-listed and installed in accordance with the instructions found in "Connecting The Dryer To House Vent" on page 6 of this KIT WX08X10077 (INCLUDES 2 ELBOWS) 4" DIA METAL DUCT which extend into the interior of the exhaust vent • Provide an opening
GE DBSR GWH install
GAS DRYER POWER HOOKUP Para obtener acceso al manual de uso y cuidado en español, o para obtener A sturdy floor to support dryer and a total weight (dryer dryer If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Do not use plastic or metal foil vent indoors, which may result in:
d b af c a a ecdd f b e
If a gas leak is detected, follow the “What to do if you smell gas” instructions Mobile Home Installation Kit Part Number 346764 ELECTRIC DRYER POWER HOOKUP – CANADA ONLY Replace any plastic or metal foil vent with rigid or flexible or other fastening devices that extend into the interior of the vent
ADAD A C BC A C E B C
and follow the instructions provided with any tools listed here □ dryer If slope is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810 wire under the screw of the terminal block (hook facing right), Replace any plastic or metal foil vent with rigid or flexible heavy indoors, which may result in:
A A A A FB AEB EAED CAA ADD
BACK COVER ELECTRIC DRYER INSTALLATION INSTRUCTIONS Use a UL listed power supply cord kit marked for use with clothes dryers Place hooked ends of remaining direct wire cable wires Do not use plastic or metal foil vent VENTING or other fastening devices that extend into interior of duct and catch
installation instructions W RevA
Read and follow the instructions provided with any tools listed here For a garage installation, place dryer at least 18" (457 mm) The kit should contain: □ A UL Place hooked ends of remaining direct wire cable wires Do not use plastic or metal foil vent or other fastening devices that extend into interior of duct
installation instructions W RevB
28 déc 2016 · Do not install a clothes dryer with flexible plastic venting materials If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance The interior of the appliance and exhaust duct should be cleaned You can change the set time in the Manual Dry cycles (TIME DRY,
manual
45 Stacking kit installation t Do not install a clothes dryer with flexible plastic venting materials If flexible metal (foil type) duct is installed, it must be of a specific type identified by The interior of the dryer and exhaust vent should be cleaned periodically by ends of the three shorter wires into a hook shape 2 Remove
DLGX
opposite directions, so when set up side by side, The dryer rack protects the most delicate fabrics or a pair of IMPORTANT SAFETY INSTRUCTIONS 5 flexible metal (foil type) duct is Fasten zippers, hooks and eyes, (including without limitation, any form of commercial use, use or storage of an indoor product
A
Follow the instructions supplied with the kit. Connect Dryer Exhaust System. WARNING. To reduce the risk of fire and combustion gas accu-.
Do not modify the plug provided with the dryer: if it will not fit the outlet have a proper outlet installed by a qualified electrician. GAS DRYER POWER HOOKUP
NOTE: Do not use leveling legs supplied with dryer if installing Use a UL listed power supply cord kit marked for use with clothes dryers.
ground wire to the neutral wire see “Optional 3-wire connection” section. ? This dryer is manufactured ready to install with a 3-wire electrical supply
If flexible metal (foil type) duct is installed it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
metal (semi-rigid or foil-type) duct is installed it must be UL-listed and installed in accordance with the instructions found in "Connecting The Dryer To
ground wire to the neutral wire see “Optional 3-wire connection” section. ? This dryer is manufactured ready to install with a 3-wire electrical supply
interior surfaces with joints running in the direction of air flow. Flexible transition ducts used to connect the dryer to the exhaust duct system shall be
NOTE: If installing dryer on pedestal do not use leveling legs. Use a UL listed power supply cord kit marked for use with clothes dryers.
recommended that a qualified electrician determine that the ground path is adequate. Electrical Connection. To properly install your dryer you must determine
Installation Instructions