USB Data Link Cable Installation Guide
Power management and Remote Wake-up Function The USB Data Link Cable supports power management function of USB When either of the two connected PC gets into suspend, the USB Data Link cable will draw less than 500 A of current from it This is essential for the notebook or other mobile PC
the WOL signal If an outboard adapter is used, the appropriate 3-pin WOL cable must be plugged into the motherboard, or the adapter/motherboard must provide PCI 2 2 system support wake up via PCI bus Figure 1: The Intel PRO/100+ network adapter supports Wake on LAN as well as many of the other features of the Wired for Management initiative 3
- 100Mbps over single balanced twisted pair cable - OPEN Alliance TC10 sleep/wake-up support - Supports cable lengths up to at least 15m - 3-level Pulse Amplitude Modulation (PAM-3) line coding - Echo cancellation - Jumbo frame support up to 16KB - On-chip termination resistors for balanced UTP cable • MII/RMII/RGMII Interfaces (RGMII
LPC214x power-down mode and USB wake-up Rev 01 — 27 June 2006 Application note Document information Info Content Keywords Microcontroller, MCU, Power-down mode, Wakeup, BOD Abstract This document describes how to put the MCU into Power-down mode to save power and provides one example to wake up the MCU via USB activity
The demonstrator is intended to show LF wake-up functionality using the new six-fold LF antenna driver ATA5279 and the 3D receiver Atmel ® ATA5282 The demonstrator may also be helpful for studying systems or as a reference tool for target applications Typical wake-up applications are designed in vehicles for Passive Entry (PE) and Tire
on wake-up (EXTI lines), STM32L0/STM32L1 MCU will drive PMOS gate to '1', so that current will flow from the supercapacitor through the diode D2 to VDD /VDDA of the STM32L0/STM32L1 MCU supply pins, to keep minimum RTC domain voltage When main supply is turned on, wake-up GPIO th reshold is reached, so that I/O drives then
– Wake on LAN For more information about the supported functions, see “Using the Ethernet connector” on page 7 Maximum resolutions and refresh rates To achieve better display experience, it is recommended that you connect one or two external monitors to the dock at a time • DP output only: 3840 x 2160 pixels (30 Hz)
UTP Cable • The ADTJA1101-RMII is a daughter card carrying NXP’s TJA1101 100BASE-T1 Ethernet PHY • It adapts to micro controller development boards with SABRE connector, e g S32K148EVB
[PDF]
Wake On LAN - BeyondTrust
desktops/servers a 3-pin power connector on adapter and auxiliary power through 3-pin connector on motherboard or PCI 2 2 system support wake up via the PCI bus For mobile PCs, auxiliary power and signaling connections are provided to the PCMCIA slot to support Wake on LAN 1 Management applications that implement auto retry (deferred processing) will eventually make the change to the
[PDF]
Am79C973 PCnet™- FAST III Hardware User’s Manual
3-pin LAN Wake-Up cable is still needed in order to provide auxiliary power (+5 VSB) to Ribbon Cable AMP179979-3 Adapter Card Header AMP173977-3 AMP173977-3 AMP179981-3 Motherboard Header 1 2 3 +5 VSB GND LAN Wake-up 1 2 3 J1 P1 P2 J2 22351A-2 Functional Description 2-3 the board If Vaux is available, there is no need to use the LAN Wake-Up cable In this case, the board will
[PDF]
LAN Cable Tester - Newegg
Scan pin assignment 6 Automatic cable identification (Cable type search ) 7 Standard pin configurations and 4 user defined cable wirings memorized in CPU 8 Can save user defined cable directly after testing 9 Test for both shielded and unshielded cable types 10 Review the captured pin assignment and failure status 11 Maximum testing length is up to 3000 feet 12 Identify and trace
[PDF]
LAN8770 100BASE-T1 Ethernet PHY Transceiver - Product Brief
• OPEN Alliance TC10 support / wake-up support • Ultra low power sleep •FlexPWR® technology power management • Advanced Signal Quality Indicator (SQI) • Over-temperature and under-voltage protection • Comprehensive status interrupt support • Extended cable reach • Small footprint 32-pin VQFN (5 x 5 mm) and 36-pin VQFN (6 x 6 mm) with wettable flanks • AEC-Q100 automotive
for external LEDs Connectors RJ-45 interface connector 10-pin box-header for extension cable with RJ-45 connector with LED 3-pin wake up LAN control line
7 2 5 4 Ethernet Cable 10Gbps 7 5m 129 7 6 1 Connection Cable Binder Type 711 (3-pin) After wake-up message switch transceivers of both channels
Accessories EN