Coding using an existing remote To enter the code of a new remote control without using your receiver, you will need an authorised remote control (note: the
Nice
Programmation ouverture totale : Pour mémoriser votre télécommande faire 1 appui courtsur le bouton de programmation RADIO La led radio va clignoter au
Programmation simplifiee telecommande NICE code tournant
The Red LED Indicator next to the Learn Button will turn on Remove the Green and White wires from terminal number 3 and 4 on the receiver (see Figure 1) and
apollo flor s receiver programming guide
remote, as well as program the remote using the dipswitches directly above the battery (on FLO1, FLO2 and FLO4 remotes) (See right) Notes • FLOR-S (Rolling
flopen
those described in this manual should be considered improper and forbidden • Other product 2 green flashes = transmitters with O-Code, O-Code/A or FloR, FloR/A encoding system green LED B: after 6 seconds it will light up then switch off After a few seconds it 5 * = No remote control memorised During operation:
is a mm
described in this manual should be considered improper and forbidden WARNINGS The OXIBD/A receiver is compatible with the “O-Code/A”, “FloR/A” one-way radio encoding systems, and with the ON Disconnect power supply / Restore power supply 5 s Wait > 5 sec < 5 # = No remote control memorised
idv a en
3÷6 1 6 6 2 3 5 4 4 4 4 1 1 Nice Neo 101 Alphabetic index Control systems and accessories Ergo, Plano, NiceWay, Flor-s, Flo, VeryVE, VeryVR, Smilo Range of motor settings to be re-set or the replacement of the remote control if
nice screen control systems en
Take an existing working transmitter and press the button that normally opens your gates/ door 3 times slowly 3 Press the button once that you would like to
File
The programming manual is the same as original remote control If our manual is not clear, you can search manual in google, youtube also can contact us via
Nice Manual
Coding using an existing remote. To enter the code of a new remote control without using your receiver you will need an authorised remote control (note:
While the red light on the receiver is turned on press and hold the Primary Button on your 2 Button Transmitter (see.
control unit with incorporated receiver for radio remote control. ROAD 0.25 m/s; the control unit allows for programming speeds of: 0.13 m/s or 0.25 m/s.
devices in the system refer to the general manual “Nice-. Opera System Book 433
NICE FLORS. NOVOFERM. AAVAQ. AT-4N. FAAC XT4 433RC. KEY TXB-42R. ATA PTX4. GBD AU1600. Nice-Smilo. ROSSI. Codiplug NOV2. MotorLine MX4SP DSM. DEA MIO TR2.
remote as well as program the remote using the dipswitches directly above the battery (on FLO1
NICE(NICE Flor-s). DEA. PECCinin. FADINI. EQUO. Sommer. Sommer. V2. ATA(PTX-4). Motorline. Motorline. DOORHAN. (TRANSMIT TER4). HORMAN. (EcoStarRSC2-433).
Nice FloR/A wireless remote con- trols to/from a gate installation. The ... on the remote control(s). Wirelessly add new remote control to the SMXI/A Plug-In ...
21 Jun 2018 Menu for adding a Nice remote control. ... (s) and through “User's details” click on the “user used as a template” field. If “Yes” is selected ...
Nice FloR/A wireless remote con- trols to/from a gate installation. The following procedures detail the steps to assign a remote control add a new remote ...
Coding using an existing remote. To enter the code of a new remote control without using your receiver you will need an authorised remote control (note:
Programming Instructions For NICE Transmitter (Remote). To NICE FLOX2R Receiver. Press and release the Yellow Learn Button on the receiver inside the Apollo
1): the SPA5 accessory is required for overhead garage doors. The control unit is equipped for installation of a 433.92 MHz radio receiver with FLOR coding. The
Apr 18 2018 control unit with incorporated receiver for radio remote control. ... During the manoeuvre the light flashes at intervals of 0.5 s.
Press and retain pressed the button of the original remote control that you want to copy until the remote's led will turn on with a fix light and then emits a.
electronic control unit and a connector for the SMXI or OXI radio remote control 10 s. N.B.: points 3 and 4 can be repeated during the same programming ...
L'opération provoque l'effacement de tous les codes contenus dans la mémoire (elle redevient vide). Garder la touche du récepteur enfoncée
built-in programming functions for adding or removing Nice FloR/A wireless Verify that the Nice remote control(s) can control the gate by pressing one.
remote as well as program the remote using the dipswitches directly above the battery (on FLO1
Press and retain pressed the button of the original remote control that you want to copy until the remote's led will turn on with a fix light and then emits a.
This transmitter belongs to the “Era Flor” range of products manufactured by Nice The transmitters in this range are with vari-able code (rolling-code)and are designed for the control of automatic door openers gate openers and similar devices: any oth-er use is improper and prohibited! Models with 1 2 4 keys are available (fig
Nice Flor-S Instructions www remotepro com au Coding using an existing remote To enter the code of a new remote control without using your receiver you will need an authorised remote control (note: the first remote control must always be entered using the receiver key)
M FLO1R-S FLO2R-S FLO4R-S FLO1R-SC FLO2R-SC FLO4R-SC is in compliance with the essential requirements and other relevant provi-sions of Directive 2014/53/EU The declaration of conformity may be con-sulted at www niceforyou com IMPORTANT: FLO1R-S/U FLO2R-S/U FLO4R-S/U (code for USA: FCC ID - PML433FRS; code for Canada: IC
English - 1 Original instructions ENGLISH1 – PRODUCT DESCRIPTION AND INTENDED USE This receiver is part of the “Flor” series by Nice spa This series of receivers is intended for use on the Control units featured in automated systems for gates garage doors and road barriers
The FLO series radio control device is a radio system working at a frequency of 433 92 Mhz which remote controls door opening d evices gate opening devices and similar pieces of equipment The system works by transmitting and receiving a digital code featuring 1024 combinations for each transmitter button
Nice FLO and FLO-RS Remotes Copyright © 2013 EasyGates Ltd - www easygates co uk Step One Press down on the bottom of the remote as shown to the right Step Two The remote should flip open from the bottom revealing the battery Gently remove the front cover from the remote (See left) Step Three You can now change the battery of your
NICE FLORS Program Instruction 1 If you have a Nice Flors receiver Please follow the steps to do the program i Press LEARN button which is on the Receiver once the Signal LED will flash ii Press one button of the transmitter Signal LED will be steady iii Press the same button of the remote again LED will flash