than that specified in this manual 2 – PRODUCT TECHNICAL SPECIFICATIONS • For all models – The receiver handles “Flor” type radio encoding with a
IS A MM
Press and release the Yellow Learn Button on the receiver inside the Apollo Box (see Figure 1) The Red LED Indicator To NICE FLOX2R Receiver Press and
apollo flor s receiver programming guide
Programmation ouverture totale : Pour mémoriser votre télécommande faire 1 appui courtsur le bouton de programmation RADIO La led radio va clignoter au
Programmation simplifiee telecommande NICE code tournant
To enter the code of a new remote control without using your receiver, you will instructions, so please refer to your manual But for a typical NICE FLOX2R
Nice
radio receiver which receives the commands sent by a transmitter Special manual release of the gearmotor for manual movement of the gate PRODUCT
NICE RO
ANLEITUNGS- HEFT INSTRUCTIONS MANUAL Radiomandos de cuarzo Nelle versioni FLOX1, FLOX2, FLOXB2, la selezione della tensione viene fatta tramite il FLOXM FLOXM220 receiver series, the output of the channels is done with different A B F o r A B F K I T aerial, fairly good results can be had by using
registered offices of Nice S p a , before printing of this manual The FLOX1, FLOX2, FLOXB2 and FLOXM receivers can be powered by 24V ac/dc or 12V ac/ dc
flox
Tento manuál je určen pouze pro technický personál, který má příslušnou přijímače s modulem BM 250, 1 nebo 2 kanály (FLOX1R, FLOX2R, FLOXB2R)
FLOX R
17 (FLOXIR-FLOXI2R) 98 x 41 h 25 (FLOX1R FLOX2R) 105 x 68 h 32 ( FLOXB2R) POIDS: 24 g FLOXIR ñ FLOXI2R, 59 g FLOX1R-FLOX2R - 82 g FLOXB2R
telecommande nice notice flor
MC824H 1 control unit with OXI plug-in receiver MOFB 1 couple of external photocells designed for connection by Nice BlueBUS MOSE 1 key selector switch
nice cat gate door en
EN. English - 1. Original instructions. ENGLISH. 1 – PRODUCT DESCRIPTION AND. INTENDED USE. This receiver is part of the “Flor” series by Nice spa. This.
Original instructions. ENGLISH. 1 – PRODUCT DESCRIPTION AND. INTENDED USE. This receiver is part of the “Flor” series by Nice spa. This.
Instructions et recommandations pour l'installateur Open the receiver box and remove the board with care (FLOX1 FLOX2
Programming Instructions For NICE Transmitter (Remote). To NICE FLOX2R Receiver. Press and release the Yellow Learn Button on the receiver inside the Apollo
EN - Instructions and warnings for installation and use Nice declines all ... For further information consult the radio receiver instruction manual. To.
Nice. Radio receiver. IT - Istruzioni ed avvertenze per l'installazione e l'uso tate in questo manuale è da considerarsi improprio e vietato!
If necessary change the transmission format of the channel/s to match the receiver/s.(Page 2 table E). 3. Pair your new E-Pad O? wireless keypad with the
registered offices of Nice S.p.a. before printing of this manual. The FLOX1
modular receivers. FLOXMR. FLOXM220R. Installation instruction manual Receivers with a terminal connection 1 or 2 channels (FLOX1R
Nice Flor-S Instructions To enter the code of a new remote control without using your receiver ... But for a typical NICE FLOX2R Receiver
This receiver is part of the “Flor” series by Nice spa This series of receivers is intended for use on the Control units featured in automated systems for gates garage doors and road barriers Any other use is to be considered incorrect and forbidden! The manufacturer shall not be held liable for damage due to improper use of the product
This receiver is part of the “Flor” series by Nice spa This series of receivers is intended for use on the Control units featured in automated systems for gates garage doors and road barriers Any other use is to be considered incorrect and forbidden! The manufacturer shall not be held liable for damage due to improper use of the product
But for a typical NICE FLOX2R Receiver the programming procedure is as follows: 1 Press the learning button on your receiver for 1-2 seconds The LED will turn on for 5 seconds Within 5 seconds complete the next step 2 Press a button on your new remote until the LED on your receiver turns off 3
NICE KX2 Connection of your receiver: 1 Unplug your motor 2 Check that your receiver is supplied with a 12V or 24V power supply by the circuit board of your motor is greater (for example 220V) you will have to transformer 3 Make the following connections with the electric - Connect channel 1 between
FLOXIR FLOXI2R AERIAL 2ND RELAY OUTPUT 1ST RELAY OUTPUT POWER: from 20 to 28 V direct or alternate normally supplied by the unit 1" RELAYOUTPUT: free contact of a normally open relay used for unit command 2"d RELAY OUTPUT: free contact of a normally open relay available on specific unit terminals (oniy on 2-channel receivers) AERIAL:
the instruction manual of the relative control unit 3 – PRODUCT INSTALLATION Install the receiver by plugging it into the control unit (fig 1) Caution! – Before connecting or removing the receiver disconnect the control unit from the power supply The aerial supplied must also be installed connecting it to the
Receiver