Arduino
After flashing the Arduino with the code below open the serial monitor and set it Arduino. Gravity Analog pH Sensor / Meter. Sample Code. Revised 6/20.
Arduino
After flashing the Arduino with the code below open the serial monitor and set it Arduino. Gravity Analog pH Sensor / Meter. Sample Code. Revised 3/22.
Arduino Uno EC sample code
After flashing the Arduino with the code below open the serial monitor and set it to append carriage return only and then set the baud rate to 9600.
Arduino Mega EC Sample Code
Atlas-Scientific.com //a string to hold the data from the Atlas Scientific product ... //This code will output data to the Arduino serial monitor.
Arduino Mega pH Sample Code
After flashing the Arduino with the code below open the serial monitor and set it to append carriage return only and then set the baud rate to 9600.
Arduino
After flashing the Arduino with the code Arduino. Gravity Analog ORP Sensor / Meter. Sample Code. Arduino Uno. Arduino Mega.
Arduino sample code EZ COM
This software was made to demonstrate how to quickly get your Atlas Scientific product running on the Arduino platform. An Arduino Duemilanove board was
Ardunio I2C EC sample code
Arduino I2C. Conductivity Sample Code. TM. Click here to download the sample code center sheild. BNC. Arduino MEGA www.arduino.cc.
Arduino sample code EZ COM MEGA
This software was made to demonstrate how to quickly get your Atlas Scientific product running on the Arduino platform. An Arduino MEGA 2560 board was used
Ardunio I2C pH sample code
9600 baud. Arduino I2C. pH Sample Code. Revised 7/19. Click here to download the sample code center sheild. BNC. Arduino MEGA www.arduino.cc.
AtlasScientific
Biology Technology
This software was made to demonstrate how to quickly get your Atlas Scientific product running on the Arduino platform. An Arduino MEGA 2560 board was used to test this code.This code was written in the Arudino 1.0 IDE
Modify the code to fit your system.
**Type in a command in the serial monitor and the Atlas Scientific product will respond.** **The data from the Atlas Scientific product will come out on the serial monitor.** Code efficacy was NOT considered, this is a demo only.The TX3 line goes to the RX pin of your product.
The RX3 line goes to the TX pin of your product.
Make sure you also connect to power and GND pins to power and a common ground. Open TOOLS > serial monitor, set the serial monitor to the correct serial port and set the baud rate to 38400. Remember, select carriage return from the drop down menu next to the baud rate selection; not "both NL & CR".EZ COM MEGA
Atlas-Scientific.comCopyright © Atlas Scientific LLC All Rights ReservedClick here to download the *.ino file
Arduino Sample Code
GND AtlasScientificTXRX
VCC centersheild PRBBNCGND
Arduino MEGA
www.arduino.cc AREF GND13121110
98765432
T X 1 R X 001234567RESET3V3891
0 1 1 1 2 1 3 1 4 1 5 2224
26
28
30
32
34
36
38
40
42
44
46
48
50
52
31
33
35
37
39
41
43
45
47
49
51
53
TX3 14RX3 15TX2 16RX2 17TX1 18RX1 19SDA 20SCL 21
PWM PWRDIGITAL
ANALOG IN
COMMUNICATION
5VGND GND VIN ICSP 1String inputstring = "";
String sensorstring = "";
boolean input_stringcomplete = false; boolean sensor_stringcomplete = false; //a string to hold incoming data from the PC //a string to hold the data from the Atlas Scientific product //have we received all the data from the PC //have we received all the data from the Atlas Scientific //product void setup(){Serial.begin(38400);
Serial3.begin(38400);
inputstring.reserve(5); sensorstring.reserve(30); }//set up the hardware//set baud rate for the hardware serial port_0 to 38400 //set baud rate for software serial port_3 to 38400 //set aside some bytes for receiving data from the PC //set aside some bytes for receiving data from Atlas Scientific //product void serialEvent() { char inchar = (char)Serial.read(); inputstring += inchar; if(inchar == '\r') {input_stringcomplete = true;} } //if the hardware serial port_0 receives //a char //get the char we just received //add it to the inputString //if the incoming character is aSerial3.print(inputstring);
inputstring = ""; input_stringcomplete = false; }//here we go... //if a string from the PC has been received in its entierty //send that string to the Atlas Scientific product //clear the string: //reset the flag used to tell if we have received a completed //string from the PC if (sensor_stringcomplete){Serial.println(sensorstring);
sensorstring = ""; sensor_stringcomplete = false; }//if a string from the Atlas Scientific product has been//received in its entierty //send that string to to the PC's serial monitor //clear the string: //reset the flag used to tell if we have received a //completed string from the Atlas Scientific productquotesdbs_dbs19.pdfusesText_25[PDF] Initiation ? la mise en oeuvre matérielle et logicielle de l 'Arduino
[PDF] Arduino Programming Notebook - pdf - Arduino Playground
[PDF] Arduino - Reference - NITC
[PDF] Pour bien démarrer - Technozone51
[PDF] ARDUINO MEGA2560 ADK (for Android)
[PDF] Arduino - Premiers pas en informatique embarquee - Le blog d
[PDF] PDF Projets Arduino pour les Nuls ePub
[PDF] Télécharger Arduino Pour les Nuls, édition poche PDF
[PDF] PROGRAMMATION ARDUINO
[PDF] schematics in pdf - Arduino
[PDF] Package 'AUC ' - R
[PDF] Licencias de salud ocupacional - Ministerio de Salud y Protección
[PDF] Première connexion ? Base Elèves Premier Degré
[PDF] 1ere utilisation d une clé OTP - Lyon
