Please read this manual thoroughly before operating the LPS Inverter System 2 Battery charger: Fully automatic dual-mode with temperature compensation supplied to the, the dual color (SDT STATUS) LED indicator will illuminate,
| Previous PDF | Next PDF |
[PDF] User manual - cloudfrontnet
This would significantly reduce the battery life span Only use the charger provided by SDT The charging time will typically be 6 hours When the LED of the
[PDF] EN SDT universal charger user guide - SDT Ultrasound Solutions
Commercial Document DC PWSP DAT 001 FUPWSPUN-1 SDT Universal Charger User Guide Guide d'utilisation du Chargeur Universel SDT FUPWSPUN -1
[PDF] EN SDT Universal charger user guide - SDT Ultrasound Solutions
user guide Please hold Specific for SDT170, SDT200 and SDT270 Ni MH battery pack Use: Four red flashes every 5 seconds: Timeout Rapid charging
[PDF] USER MANUAL - MLT
2 déc 2020 · This manual contains instructions specific to LUBExpert App Firmware and its interface to SDT Universal Battery Charger w/o Cord
[PDF] SDT International sa-nv • Bd de lHumanité 415 • B-1190 Brussels
Universal voltage battery charger (110-240V AC 50/60Hz) • Manuals and applicable software on memory flash drive or downloadable • Belt attachment and
[PDF] OPERATING AND BASIC TRAINING GUIDE - SportDOG
When the unit indicates the battery is low (red light indicator) it is time to recharge the unit CHARGE THE REMOTE TRANSMITTER 1 Lift the rubber cover
[PDF] Installation And Operation Instructions - Mule Lighting
Please read this manual thoroughly before operating the LPS Inverter System 2 Battery charger: Fully automatic dual-mode with temperature compensation supplied to the, the dual color (SDT STATUS) LED indicator will illuminate,
[PDF] Installation Instructions and User Manual - hubbellcdn
Please read this manual thoroughly before operating the LiteGear Inverter System Battery charger: Fully automatic dual-mode with temperature compensation supplied to the unit, the dual color (SDT STATUS) LED indicator will illuminate,
[PDF] Power Supply Guide - XP Power
of magnetic windings for use in our power converters in 2012 The 1000W external PSU compliant to MIL-STD 461F Battery charging - Power supply
[PDF] February 16, 2021 Product Guide - AMETEK ORTEC
precautions contained in the manual furnished with Includes battery, charger, and cables for all Detective and trans-SPEC-100 models ASC2-SHIELD-STD
[PDF] En sécurité sous la cagoule
[PDF] En sécurité sur la route avec mon convoi agricole - France
[PDF] en seignement
[PDF] en seignement - Ministère de l`éducation nationale
[PDF] en seine-et-marne - Transport Public
[PDF] EN SEPTEMBRE - Mesnil - Anciens Et Réunions
[PDF] En septembre à la Maison de la Nature du Sundgau
[PDF] En service ce mois-ci Ancien Responsable musique
[PDF] en soins palliatifs - Association Québecoise de Soins Palliatifs - Santé Et Remise En Forme
[PDF] en sologne - ensemble immobilier avec local commercia - E
[PDF] EN SONDE DES SENTIMENTS VERS L`UNIVERS - France
[PDF] En souvenir de Moche Catane ל״ז In loving memory - Des Bandes Dessinées
[PDF] En stage à Cap au Large sur Laisse Dire
[PDF] En stock - DBM Automobiles
Installation And Operation Instructions
TrueSinusoidal
Output Power
LPS-375 Model
LPS-600 Model
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS:
i ot connectSAVE THESE IMPORTANT SAFETY INSTRUCTIONS
7DEOHRI&RQWHQWV
3DJH0DLQWHQDQFH
Note: Lead Calcium battery performance rated at 25°C (77°F) for load T able 1 System weights shown include installed batteries MODEL INPUT/OUTPUT CAPACITY SYSTEM SYSTEM NUMBER BATTER Y BATTER Y AC INPUT THERMALNUMBER VOL TAGE For 1
1/2 Hrs. WEIGHT EFFICIENCY OF VOLT AGE CURRENT CURRENT (MAX) OUTPUT (BTUs) Watts/VA) Lbs. Kg. (Full Load) BATTERIES (VDC) (Amps) 120V AC 277VAC On-Line Emergency 9$& /369$&LPS-375LPS-600
FP FP Lengthy storage of batteries will cause irreversible damage to the cells Failure to connect inverter system batteries to an energized charging circuit within 90 da ys from the date of shipment will void the battery warranty. -age location because hydrogen is concentrated under the vent cap of eac h cell of the battery. Hydro-gen is highly explosive, and is hard to detect because it is color less, odorless, and lighter than air. inverter Systems are UL Listed for 20° to 30° C (+ 68° to +86° F) operation. Battery performance and service life is maximized if the operating tempe rature is maintained at 25° C (77° F). tures will reduce battery life. Typically , at 35° C (95° F), battery life will be half of what it would b e atnormal temperature of 25° C (77° F). At 45° C (113° F), battery life will be one-fourth of normal.
The air around the unit must be clean, dust-free, and free of corrosive chemicals or other contami- nants. Do not place the inverter system or batteries in a sealed room or container. ration See eration See and A combination of the operating modes described above. See See ,'',35%8,*1#$% .3+ .0$+$%,53$+)(0,3+$9$3+$3*%$**,35% -(.+%+(3(*$41$$+&3,*0.*,35,3$'$05$316'(+$ : Wear protective clothing, eye-wear, rubber gloves and boots. Batteries c ontain corrosive acids or caustic alkalis and toxic materials and can rupture or leak if mistreate d. Remove rings and metal wristwatches or other metal objects and jewelry. Don"t carry metal objects in pockets where the objects can fall onto the batteries or into the inverter system. Tools must have insulated handles so that they will not short battery terminals. Do not allow a tool to short a battery terminal to another battery terminal or to the cabine t at any time. Do not lay tools or metal parts on top of the batteries, and do not lay any objects where they could fall onto the batteries or into the cabinet. Install the batteries as described in this manual. When connecting cables, never allow a cable to short across a battery"s terminals or to the cabinet.Keep the cable away from any sharp metal edges.
Install the battery leads so they cannot be pinched by the inverter system cover/door. Where conductors may be exposed to physical damage, protect conductors i n accordance with NEC requirements.Full voltage and
current are always present at the battery terminals. The batteries used in this sys- tem can produce dangerous voltages, extremely high currents, and possibl e risk of electric shock. Batteries may cause severe injury if the terminals are shorted together or to ground (earth). Be extremely careful to avoid electric shock and burns caused by contact ing battery terminals or shorting terminals during battery installation. Do not touch uninsulated battery terminals. who is familiar with battery systems and required precautions must insta ll and service the batteries. Any battery used with this unit shall comply with the applicable require ments for batteries in the standard for emergency lighting and power equ ipment, UL 924. Cabinets are designed to be used with, and batteries must be replaced by identica l cells or a Manufacturer approved equivalent. If using substitute batteries not supplied by the M anufacturer, the unit"s ULlisting will be void, and the equipment may fail to perform properly. The installation must conformto
national and local codes as well. Keep unauthorized personnel away from batteries.Battery
P lacement The L PS -375 models are provided with (5) 12V Lead Calcium batteries (60Vdc string). The L PS -600 Models are provided with (8) 12V Lead Calcium batteries (96 Vdc string).
LPS -375: Carefully place all batteries in the unit battery (lower) compartment with positive (+) red
terminals facing o utwards an d u pwards. Position batteries in the central location towards rear of the compartment. C arefully i nstall b attery r etention b racket with t he supplied h ardware.LPS-600: Carefully place (4) batteries in each of the battery (central and lower) compartments with positive
(+) red terminals facing outwards and upwards. Position batteries in the central locations towards rear of
the compartments. Carefully install battery retention brackets in each compartment with the supplied hardware.Battery Wiring:
CAUTION: To prevent possible damage to the unit when connecting batteries, verify that the unit battery
circuit breaker CB-1 is in the OFF position.Connect batteries with supplied wiring jumpers using hardware provided with batteries. For LPS-375 refer
to Battery Wiring Diagram 1. For LPS -600 refer to Battery Wiring Diagram #2.