[PDF] Instructions for Miniflam AP Piezo Ignition Torch

Instructions for Miniflam AP Piezo Ignition Torch The miniflam “AP” Blue Head can be characterized by a very sharp flame that can be adjusted in length from

Instructions for Miniflam AP Piezo Ignition Torch - MonsterSlayercom

Instructions for Miniflam BP Piezo Ignition Torch The miniflam “BP” Green Head can be characterized by a very sharp flame that can be adjusted in length from

[PDF] miniflam ¨GP¨ - RMO Europe

MULTI-PURPOSE TORCH ADJUSTABLE Loin de toute flamme, visser à fond la cartouche de gaz MINIFLAM, sur la tête du chalumeau, puis INSTRUCTIONS FOR USE 1 Piezo ignition: air is needed for proper ignition, therefore

[PDF] c ,1,t

from Miniflam Torch, thereby retaining the balance of gas inside when FL Flared Manual Head 33-0315 AP Piezo Ignition Head 33-0326 411111 BP Piezo

[PDF] PRODUCT CATALOGUE 2019 - Durodent Dental Supplies

With the help of a guide according to August Bruguera's philosophy, different gingiva- APA-F Articulating Paper Forcep, Stainless Steel, 1 State-of-the art piezo electric ignition system MFMG Miniflam Butane Torch Refill Gas, 300g, Red

[PDF] R&AC + HYDRAULIC & PLUMBING - General Gas

Instruction K-LEAK TESTER N2H2 Leak Testing kit N2/H2 for Refrigeration A/ C Systems K-Leak Testers is an essential equipment that allows the

[PDF] Selva Katalog Umschlag_2018_ENindd - Selva Shop

plete with fastening lugs, gong, key and installation instructions Length ap- prox mm 2 MINIFLAM Hand Torch With piezo ignition, 20 ml butane gas tank

[PDF] 2002 December - American Welding Society

1 déc 2002 · for transportation infrastructure projects, in compliance with ap- plicable law, while Our welding process experts will help you determine which of our '~ Miniflam USA, Inc Motoman, Inc tomized solutions for welding torches and accessories Use of lighter A piezoelectric transducer having a reso-

[PDF] Beginning: Hi-Fi glossary - American Radio History

3 oct 1979 · 'HintsonSoldering' containing clear instructions to make everyjob easy Ersin Multicore Map 74367 4368 150p 74390 2000 74393 ma 74490 225p 74 LS our fabulous Piezo Horns which handle a the electric ignition on the gas cooker would 57 Hot stuff The new Miniflam blow torch now be-

Instructions for Miniflam AP Piezo Ignition Torch

The miniflam "AP" Blue Head can be characterized by a very sharp flame that can be adjusted in length from 1/4" to 1/2" by adjusting the gas flow. APERTURE: For proper ignition, apertures on the AIR regulator band must be 3/4 opened. AIR CONTROL REGULATOR: (for a more or less rigorous flame, uncover the apertures accordingly

by twisting the blue band). Air is needed for proper ignition, therefore, make sure the apertures on the air

control band blue) is 3/4 to completely open. PIEZO IGNITION BUTTON: TIP: The Piezo ignition button produces a spark at head tip to ignite torch.

GAS CONTROL REGULATOR:

(for "on and off" operation and for adjusting the flame size accordingly by twisting the red band).

DIRECTIONS AND METHOD OF USE

ASSEMBLY PROCEDURES: Before starting this procedure, make sure that there are no other burners or open flames in use in the immediate area. Screw the 40 gram Miniflam gas

cartridge/refill or S rechargeable canister clockwise using the red band on the torch head until hand

tight. As a small amount of gas will be released during the initial portion of this operation, continue

to tighten torch head on gas cartridge until the sound of the gas seizes. Do not force or over tighten. TO IGNITE: Unscrew the red band 1/4 turn counter-clockwise to start the gas flow, and ignite by depressing Piezo button. To stop, tighten the red band clockwise until gas seizes to flow. Tip: Use yo ur thumb against the Piezo Arm to rotate the head to the right to start gas flow, then depress Piezo ignition button to light. To turn the unit off, rotate Piezo Arm to the left.

FUEL REPLACEMENT:

To set another torch head on the Miniflam gas or to replace a Miniflam 40 gram

gas cartridge/refill, just unscrew the torch head completely from the gas cartridge using the red band.

Again,

some gas may escape during a portion of this operation; therefore, make sure that there are no other burners or

open flames in use in the immediate area. The refill cartridges are self sealing when unscrewed so they can be

transferred and used with other miniflam torch heads while gas lasts.

Jet /injector Replacement: In case of clogged jet or injector, (symptom no gas flow) replace or clean the jet/injector.

Remove gas canister. Remove top hood section by loosening screw in blue or green air control band. Remove the

exposed jet/injector very carefully using a small wrench. When reassembling the torch, screw in and tighten new or

cleaned jet/injector by hand. Tighten jet/injector carefully with small wrench. (Caution, Do not over tighten!) Loose

fittings, particularly the jet, will cause improper flame. Insert the ceramic shroud over the armature making

sure that

Piezo electrode slips through hole at top.

Install hood section to line up the apertures in the open position.

Cleaning: If miniflam 223 gram gas item # 47-1602 is available, try to clean the jet/injector by injecting gas directly

into the top

of the jet/injector in a well ventilated space. Best results occur when the 223 gram can is used upside down

so that the gas used is in its liquid state. (Note: Hold the jet/injector with a small pair of pliers. Caution! Liquid gas can

cause frostbite when applied directly on finger tips.) If the jet/injector remains clogged, place the jet/injector into

mentholated spirit in an ultrasonic unit for 30 minutes, or order a new jet/injector from your supplier. (Order Jet/Injector

#36-0455 for "AP" head or #36-0456 for "BP" head.)

Optional Fuel Sources

Miniflam Piezo "AP" Torch

Head Type

(blue band) Miniflam 223 gram refill canister: Miniflam Gas has specially been formulated and balanced to deliver the

cleanest possible burning flame where clean high quality welding, soldering and brazing is a necessity. The gas has

been finely filtered to remove unwanted impurities such as paraffin which often leads to clogged jets. Always use miniflam gas to insure continuous operation of your miniflam torches. Supplies approximately 1 hours of continuous gas flow using the "A

P" type head on a charge.

Miniflam GP40 Gram Vapor Gas:

Miniflam Gas has specially been formulated

and balanced to deliver the cleanest possible burning flame where clean high quality welding, soldering and brazing is a necessity.

The gas has been finely filtered to remove

unwanted impurities such as paraffin which often leads to clogged jets. Always use miniflam gas to insure continuous operation of your miniflam torches.

This unit supplies

approximately 4 hours of continuous gas flow using the "AP" type head. Hood section

[PDF] [PDF] Instructions for Miniflam AP Piezo Ignition Torch - MonsterSlayercom