Rotary switch SW4 Rotary switch SW6 Figure 2 Model 250-500-1000-2000 all configuration operations must be carried out by specifically qualified personnel for operations on powered electronic damage to the electrical components
Previous PDF | Next PDF |
[PDF] Manual: Electric Actuators model EPI-2 IOM, Keystone - Emerson
Warning The electronic parts of the EPI-2 and all the 2 KEYSTONE Keystone ePi-2 quarter-turn electric actuator INSTALLATION AND MAINTENANCE INSTRUCTIONS B Product model for electrical connections use components
[PDF] Keystone EPI2 - Emerson
The EPI2 is an intelligent quarter-turn electric actuator designed for direct mounting to a Components - Model 2000 / E171 Part Electronic Remote Controls
[PDF] Keystone Electric Actuators, Model EPI-2
Keystone OM3 - EPI-2 LOcaL IntErfacE MOduLE INSTALLATION AND WarnIng EPI-2 actuator must be electrically isolated before WarnIng The electronic parts of the EPI-2 actuators or reconstruction of the above components are
[PDF] F02/EPI2 Quarter-Turn Electric Actuator - Biffi Actuators
Rotary switch SW4 Rotary switch SW6 Figure 2 Model 250-500-1000-2000 all configuration operations must be carried out by specifically qualified personnel for operations on powered electronic damage to the electrical components
[PDF] KEYSTONE EPI-2 ELECTRIC ACTUATORS - Applied Control
2 KEYSTONE EPI-2 ELECTRIC ACTUATORS COMPONENT PARTS - MODELS 063/E006-125/E013-250/E025-500/E051-1000/E091 Part Description
[PDF] Industrial Valve Manual - Elkhart Brass
The Keystone EPI2 electric actuators covered in this manual are designed to Integral controls unit inclusive of electric motor, motor controls, electronic Check that the information on the nameplate (Model, Serial Number, Nominal Torque, Nominal Voltage For all electrical connections, use components (cable glands,
[PDF] EPI2-MAN-652 - Regional District of Central Okanagan
14 sept 2017 · The electronic parts of the actuator can be damaged by a discharge of static The Keystone EPI² electric actuators covered in this Instruction and The EPI2 is an electric quarter-turn actuator suitable to operate a valve or damper 2 2 Check that the information on the nameplate (Model, Serial Number,
[PDF] Seimens feb_05qxd
Keystone 2- and 3-Way Resilient Seated Butterfly Valve Assemblies Copyright 60 psi; Electronic (w/and w/o Keystone Figure 777 Electric Actuator - (E2, EM and EP Assemblies) Model Electric Manual Lbs Lb -in Range (Lbs ) EPI-3 3500:1 70:1 15 240 0-10Vdc and 4-20mA Modulating Actuator Components
[PDF] 2- & 3-Way Resilient Seat Butterfly Valve Assemblies 2- & 3-Way
Electronic (w/and w/o spring return): 0-10 V, 4-20 mA, Keystone Figure 222 and Figure AR2 Resilient Seat Butterfly Valves EPI 2 Electric Actuator Easily accessed control panel allows setting of torque, speed, and position All metal gearing (on most models) 0-10Vdc and 4-20mA Modulating Actuator Components
[PDF] Keystone Knife Gates, Figure 952
[PDF] Keystone Module RJ45 female > LSA Cat.6
[PDF] Keystone TFoundry - Klingspor Museum
[PDF] Keystones Appartement à louer € 1.190 - Anciens Et Réunions
[PDF] Keystones Appartement à louer € 1.400
[PDF] Keystones Maison à vendre € 535.000
[PDF] keyTec AZ - Winkhaus
[PDF] keyTec RAP
[PDF] Keytis 2-RTS Keytis 4-RTS Ref:1840044, 1840034 - France
[PDF] Keytrade Bank : bénéfice net de € 1,568,000 au troisième trimestre
[PDF] Keytrade Bank Carte VISA Gold Assistance voyage - France
[PDF] Keytrade Bank dans le giron du Crédit Agricole
[PDF] Keytrade Bank enrichit sa gamme de produits bancaires en ligne
[PDF] Keytrade Bank est à Genève !
F02/EPI2 Quarter-Turn
Electric Actuator
Base and OM1 Card
F02/EPI2 Base and OM1 Card
April 2018
Quick Start Guide
VCIOM-08536-EN Rev. 0Base Card
F02/EPI2 Quarter-Turn Electric Actuator
Figure 1
Model 063-125
Green LED
Power ONDip switch
SW3Push button
SW5Red LED
Enter configuration
Rotary switch
SW4Rotary switch
SW6Figure 2
Model 250-500-1000-2000
Dip switch
SW3Green LED
Power ON
Rotary switch
SW6Rotary switch
SW4Red LED
Enter configurationPush button
SW5Table 1.Operating Times
ModelNominal torque
(Nm/lb.in.)Operating time (secs 90
o ) at selected step 86406363/600152848
125125/1300152848
250250/2500152848
500500/5100152848
10001000/9100244580
20002000/1770053100180
Note: (*) FactoryPRE-INSTALLATION: See VCIOM-2881 INSTALLATION AND MAINTENANCE INSTRUCTIONS. Not performing the following procedures will invalidate the product warranty.
INSTALLATION: To assemble the actuator onto the valve proceed as follows: a. Verify proper mounting hardware. b. Verify proper electrical service to the actuator c.d. e. Install the actuator onto the valve so that the shaft out put drive enters the groove of the stem extension. This coupling must take place without forcing and only with the weight of the actuator.
f. Ensure actuator and valve are in same orientation when bolting together. g. With the handwheel, operate the actuator to verify it moves the valve smoothly.WARNING
cards. Hazardous voltages may be present. Before connecting power to the actuator, check that the voltages are correct and according to the nameplate data. Improper power supply will cause permanent
Quick Start Guide
VCIOM-08536-EN Rev. 0
F02/EPI2 Base and OM1 Card
April 2018
See table 1Rotary Switch SettingsConfigurations
Move switch SW4 to position
indicated in each rowMove switch SW6 to position
indicated in each row SW3 SW5Red LED
SW3CLOSE LIMIT by position21 (*)
PUSHLED lights up once
Drive the actuator to
the CLOSE position using the handwheel 00OPEN LIMIT by position31 (*)LED lights up once
Drive the actuator to
the OPEN position using the handwheel 10CLOSE LIMIT by torque20 (*)
Operate the
actuator to direction bylocal/remote control and wait until it stops byOPEN LIMIT by torque30 (*)
CLOSING speed44
6 (*) 8LED lights up once
OPENING speed5
% CLOSING torque62 = 50%5 = 75%
9 = 100% (*)% OPENING torque7
CW/CCW8
0 = CW (*)
1 = CCW
BLINKER/local selector4
0 = off (*)
1 = Blinker
2 = Loc. Sel.
Quick Start Guide
VCIOM-08536-EN Rev. 0
F02/EPI2 Base and OM1 Card
April 2018
OM1 Card
F02/EPI2 Quarter-Turn Electric Actuator
Figure 3
Input Signal Configuration
SW5Confirmation Push Button
SW2Rotary Switch
SW8 SW7 SW9
EnterConfiguration
Red LED
Input Signal Configuration
SW3Enable Configuration Mode
SW4SW6 SW1
Output Signal Configuration
Hardware Configuration
Input Signal
SW3SW5
1210-10VONOFFOFF
4-20mAOFFONON
Output Signal
SW1SW6
123410-10VOFFONONOFFON
4-20mAONOFFOFFONOFF
Rotary Switch Settings
Configurations
Move switch SW8 to
position indicated in each rowMove switch SW7 to
position indicated in each rowMove switch SW9 to
position indicated in each row SW4 by SW2Red LED
SW4RELAYS LS3-LS570=break
1=make (*)
Any position
SW4 to ON PushLED lights up once
SW4 to 1 (Run Setting)RELAYS LS4-LS68
POSITION Relays LS300 to 9 [0=(*)]
POSITION Relays LS410 to 9 [3=(*)]
POSITION Relays LS520 to 9 [7=(*)]
POSITION Relays LS630 to 9 [9=(*)]
SET Input as "4-20mA"9
0=off1=on (*)
4SET 0% input 4-20mA
40 = 4mA (*)
Any position
SET 100% input 4-20mA1 = 20mA (*)
SET Input as "0-10V"
90=off (*)
1=on 5Feedback mA or Vdc
2= mA (*)
3= Volt
1Modulation
0=off (*)
1=on 3See table 2
Table 2.
SW7Position Relays0123456789
WARNING
For complete Instruction & Warning see the VCIOM-01494 INSTALLATION AND MAINTENANCE INSTRUCTIONS. HARDWARE
OFF (NO power supply).SW3 and SW5 position in order to set the INPUT signal type. Note: (*) Factory default data