[PDF] [PDF] MswLogo Getting Started

MswLogo commands are typed into the bottom (Commander) window Commands can be entered letters (usually the first and last letters of the word), except



Previous PDF Next PDF





[PDF] CLASS 3 CHAPTER 4: INTRODUCTION TO LOGO - Exploring IT

Write the LOGO primitives to draw the letters N, M, V and Z a Commands to draw letter 'N' FD 50 RT 135 FD 70 LT 135 FD 



[PDF] Module 5 Exploring Control - Assets - Cambridge University Press

5 1 Exploring control MSWLogo Type the following list of commands to draw a square with sides Repeat for 3 more letters, M, W and Z, or any letters of your 



[PDF] Example of commands

MSW Logo "Turtle Graphics" Primitive Command Summary you can draw out on grid paper (for a graphic image) or sketch out in words the steps required to 



[PDF] Chapter 11 Talk To Your Computer

Logo can also display alphabetic and numeric characters using the CHAR or The input to the MSW Logo command, SETTEXTFONT, describes a font and the 



[PDF] Programming in LOGO - ABZinfethzch

The command forward 100 or fd 100 moves the turtle 100 steps forward: The only restrictions on the name are that it consists only of letters and digits, and that



[PDF] MswLogo Getting Started

MswLogo commands are typed into the bottom (Commander) window Commands can be entered letters (usually the first and last letters of the word), except



[PDF] A Very Basic Introduction to MSW Logo Programming 1 GETTING

Note that the two words that appear "to" and "end" are the first and last words respectively that you will need to use when writing any procedure Close the window



[PDF] 1 Fill in the blanks 10 [Orientation, start, horizontally, slide, set

To hide the turtle you give ST command ______ ii) Lowercase letters cannot be converted to uppercase in MSWLOGO ______ iii) Show prints the input in 



[PDF] Logo Command reference - ACS Home Page

Draws an arc of radius radius, centred on the current turtle position and starting that characters such as slashes in the name are not taken to be logo operators



[PDF] 1 What is the full form of logo? - Madhav Internation School

Ans: The commands that we give to the truth are called logo primitives 13 Who developed the MSW logo? Ans: Professor Seymour papert of U S A developed 

[PDF] msw logo download for pc

[PDF] mta b31 bus schedule

[PDF] mta b36 bus route

[PDF] mta bus 50 schedule

[PDF] mta bus route

[PDF] mta bus schedule

[PDF] mta bus schedule 84

[PDF] mta bus time app download

[PDF] mta bus time app for iphone

[PDF] mta bus time app ios

[PDF] mta bus time app not working

[PDF] mta bus time application

[PDF] mta bx3 bus schedule

[PDF] mta express bus

[PDF] mta trip planner

MswLogo Getting Started

MSWlogo\LOGO Getting Started B. Grantham

MswLogo commands are typed into the bottom (Commander) window. Commands can be entered in either upper or lower case (or both).

Spaces are used to delimit (separate) commands.

Most of the commonly used LOGO commands can be abbreviated to 2 letters (usually the first and last letters of the word), except where duplication occurs:

FD___ForwarD BK___Bac

K LT___LefT RT___RighT

REPEAT no abbreviation, example: REPEAT 4 [FD 50 RT 90] note the use of square brackets here

PD___PenDown PU___PenUp PE___PenErase PPT___PenPainT (draw) (move) (rub out) (cancels erase)

ST___ShowTurtle HT___HideTurtle (speeds up screen graphics) HOME moves Turtle to the origin (0,0) and HEADING 0 ('North') Note: If the pen is down when the HOME command is issued, a line is drawn to the origin)

CS___ClearScreen

(erases graphics and sends the Turtle 'HOME')

EDALL___Edit all procedures

ERALL___Erase all procedures

SETPENSIZE [width height]

(enter two numbers but first number not used in MswLogo)

SETPC___SETPenColor [red green blue]

(each colour in range 0-255) SETSC___SETScreenColor [red green blue] (background colour)

SETFC___SETFloodColor [red green blue]

(move turtle inside shape then FILL) [255 0 0 ] = red [ 0 0 0 ] = black [ 0 255 0 ] = green [255 255 255] = white [ 0 0 255] = blue [128 128 128] = grey Procedure definitions must begin with TO procname and end with END eg. TO square

REPEAT 4 [FD 50 RT 90]

END

Parameters can be passed to procedures

eg. TO poly :sides :size

REPEAT :sides [FD :size RT 360/:sides]

END (Issuing the command 'poly 5 100' draws a regular pentagon of size 100)quotesdbs_dbs17.pdfusesText_23