[PDF] Advanced Science Letters 16-Jun-2020 The two

View - Download Advanced Science Letters

Previous PDF

Next PDF

The 1st

th, 2016, Bali, Ind 1 OPTIMIZATION OF THE PARAMETERS OF THE MANUFACTURING B1,2*, P.W. Anggoro1,2, J.Wibowo1, J. Jamari2, A.P. Bayuseno2 1)

2) Department of Mechanical Engineering, University of Diponegoro,

1) bajubawono2)

Reverse innovative design (RID) iso_diabetes) was able to speed up the design iso_diabetes raster machining 450 and step & shallow machining iso_diabetes

8 3 iso_diabetes

iso_diabetes : toolpath 0, step & shallow, PowerMill 20

INTRODUCTION

Reverse innovative design(RID) is a new method in reverse engineering by Xiuzi Ye (2008). This method was

iso_diabetes iso_diabetes: (a) patient 1, (b) patient 2

The 1st

th, 2016, Bali, Ind 2 Figiso_diabetes based on the width tolerance: (a) patient 1, (b) patient 2. iso_diabetes simply based on the smallest von misses stress

iso_diabetes used. However to determine exactly where the new design the optimal manufacturing process optimization

iso_diabetes in CNC machines by Fig Fig HSM can be defined as the process of machining by use of

The 1st

th, 2016, Bali, Ind 3 compared to the conventional method. HSM allows material results. iso_diabetes iso_diabetes that is designed as shown in Figure 2 along with iso_diabetes really fit and fit to the shape and contour of the feet of the patient. iso_diabetes

METHOD

iso_diabetes is a 3D solid CAD models, EVA iso_diabetes raster finishing 450 and 0 by PW.Anggoro, et.all (2016)

Iso_diabetthat will be done later in the research should meet the demand of Orthotic & Prostethic

6 hours for each pair.

Eva rubber specimen

Eva rubber foam with dimensions 250 x 95 x 23 mm thick are used in this experiment. The hardness of the material is

65 kg/m3, nominal size 2000 x 1000 mm nominal

36 mm, hardness read after 2s is 25

3D model iso_diabetes

3D model iso_diabetes

Figiso_diabet: (a) patient 1, (b) patient 2.

TM

The 1st

th, 2016, Bali, Ind 4 Table Old 1 NoNameFigure foot3D Scann footmale/femaleRisk classes

Tooling & CNC machine

In this paper, research is carried out using a machine Fig

Orthogonal array

iso_diabetes. iso_diabet

N7 (63 µm scale C.L. A or Ra =

T iso_diabetes0.0 is not discussed in this paper because it's already covered in previous studies iso_diabetes in this paper starts from 0.51.5 mm as shown in table

iso_diabetes optimal. Response data will be measured in the experiments of this surface roughness (Ra) and

m) biso_diabetes m= 6

84.24, with the iso_diabetes

iso_diabetes. 84.24, then ca

The 1st

th, 2016, Bali, Ind 5

has been set using the machine Rolland modella MDX 40R and EVA rubber material. Stages of the process of

Figiso_diabetes: (a) the Handyscan 700TM, (b) 3D mesh

844(e) optimize and simulation

iso_diabet iso_diabet, (h) measuring surface roughness of iso_diabet iso_diabetes a numb iso_diabetes appropriate treatment at

The 1st

th, 2016, Bali, Ind 6 FigIso_diabet with various width tolerance: (a) the left foot patient 1, (b) the right foot patie

RESULT & DISCUSSION

iso_diabetes iso_diabetes iso_diabetes. cutter and the WD40

8 is an

i N N 1 A v 2 yy k n SSR k their sample means. If the sample means differ substantially then SST will be large.

The 1st

th, 2016, Bali, Ind 7

Sum of Squares for Error,

k y y n SSE k y y n SST

Table 3. SN Ratio For L8 4.24

84.24, then the optimal results can be presented i

Table 4. Optimum iso_diabetes

84.24 exists on machining parameters for patients 1 & and 2 were on

0 iso_diabetes

CONCLUSION

84.24
iso_diabetes optimal i.e.new iso_diabetes product for patients 1

The 1st

th, 2016, Bali, Ind 8

ACKNOWLEDGMENT

REFERENCES

Anggoro P.W

Proceeding seminar of International Conference on engineering tribology and applied , Taiwan (2016), Parameter Optimatizion of strategies at CNC

International Journal of Mechatronic & Mechan

Proceding Bisstech 2016,

proceding seminar of International Conference on engineering trybology and applied , Taiwan Clin , 14,pp567

J Rehabil Res Dev

2012, The role of footware in the prevention of diabetic foot problem, J. The Diabetic Foot; Medical

Bio, 16, 289

Procedia Materials Science, 5

Journal The Diabetic Foot, Vol. 8, No.2, , pp 72

, International Journal of , Vol.9, No.5 pp.343

Computer

Material

, Vol. 53, N0. 9 pp. 1685quotesdbs_dbs48.pdfusesText_48

[PDF] advanced sciences & technologies

[PDF] advances in health sciences education

[PDF] advantages and disadvantages of e-commerce pdf

[PDF] adventure in english unit 7

[PDF] advertising esl lesson plan

[PDF] advertising lesson plans

[PDF] aec financé par emploi quebec

[PDF] aefe amerique du nord

[PDF] aeroport casablanca boutiques

[PDF] aeroport casablanca train

[PDF] aeroport mohamed 5 terminal 1

[PDF] aeroport mohamed 5 terminal 2

[PDF] aeroport mohamed 5 terminal 3

[PDF] aes clermont ferrand

[PDF] aesh 2017 macron