[PDF] H.264 HD DVR Users Manual Live configuration includes four submenus:

View - Download H.264 HD DVR Users Manual

Previous PDF

Next PDF

Thank you for purchasing our product.Please read thisuser"smanual beforeusing the product. Change withoutnoticeH.264HDDVRUser"s Manual

2

CAUTIONPlease read this user manual carefully to ensure that you can use the device correctly and safelyWe do not warrantall the content is correct. The contents of this manual are subject to changewithout noticeThis device should be operated only from the type of power source indicated on the marking label.The voltageof the power must be verified before using. If notin use for a long time, pull out the plugfrom the socketDo not install this device near any heat sources such as radiators, heat registers, stoves or otherdevice that produce heatDo not install this device near water. Clean only with a dry clothDonot block any ventilation openings. Andensure well ventilation around the machineDo not power off the DVR at normal recording condition! The correct operation to shut off DVR is tostop recording firstly, and then select "shut-down" button at the rightof the menu bar to exit, and finallyto cut off the power.This machine is indoor using equipment. Do not expose the machine in rain or moist environment. Incase any solid or liquid get into the machine"s case, please cut off the power supply immediately, andask for qualified technicians to check the machine before restartRefer all servicing to qualified service personnel. No any parts repaired by yourself without technicalaid or approval.This manual is suitable for4,8, 16channelHD digitalvideo recorders.

3

1.1Main FeaturesCOMPRESSION FORMATStandard H.264 compression with low bit rate and better image qualityLIVE SURVEILLANCESupportVGA /CVBS/HDMIoutputSupport 4/ 8/ 16 channelSDI video inputSupport channelsecurity by hiding live displayDisplay the local record state and basic informationSupport USB to make full controlRECORD MEDIA4 channelHD DVRsupport2SATA HDDor1SATA HDD if a DVD-RWwriteris installed inside8 and 16 channelHD DVRsupport8 SATA HDD or 4 SATA HDD if a DVD-RWwriteris installed insideBACKUPSupport USB 2.0 devices to backupSupport saving recorded files with AVI standard format to a remote computer through internetRECORD & PLAYBACKRecord modes: Manual, Schedule, Motiondetection and Sensor alarm recordingSupports recycle after HDD fullResolution, frame rate and picture quality are adjustable128MB for every video file packaging4/8/16audio channels availableThree record search mode: time search, event search and image searchSupport 1/4 (1080P) screen playback simultaneouslySupport deleting and locking the recorded files one by oneSupport remote playback in Network Client through LAN or internetALARMAlarm Input/Output: 4CH(4/4), 8CH(8/4), 16CH(16/4)Support schedule for motion detection and sensor alarmSupport pre-recording and post recordingSupport linked channels recording once motion or alarm triggered on certain channelSupport linked PTZ preset, auto cruise and track of the corresponding channelPTZ CONTROLSupport various PTZ protocolsSupport 128 PTZ presets and 8 auto cruise tracksSupport remote PTZ control through internetSECURITYCustomize user right: log search, system setup, two way audio, file management, disk management, remotelogin,live view, manual record, playback, PTZ control and remote live viewSupport 1 administrator and 63 users.Support event log recording and checking, events unlimitedNETWORKSupport TCP/IP, DHCP, PPPOE, DDNS protocolSupport IE browser to do remote viewSupport setup client connection amountSupport dual stream. Network stream is adjustable independently to fit the network bandwidth andenvironment.Support picture snap and color adjustment in remote liveSupport remote time and event search, and channelplayback with picture snapSupport remote PTZ control with preset and auto cruiseSupport remote full menu setup, changing all the DVR parameters remotelySupport mobile surveillance by Smartphone, Iphone, Android Smartphone, 3G network availableSupportCMS to manage multi devices on internet

4

1.2Front Panel Instructions

Notice: The pictures are only for reference; please make the object as the standard.

Front Panel of 4 CH HD DVRNoLabel NameDescription1USBConnect USB thumb drive or mouse2POWERPower indicator3REC/FOCUSManual record/FOCUS adjustment(PTZ)4Play/IRISEnter Playback/IRIS adjustment(PTZ)5REW/ZOOMREW on playback mode/ZOOM adjustment(PTZ)6FF/ P.T.Z.FF on playback mode/Enter PTZ mode7STOP/ESCSTOP playback on playback mode/Exit MENU or jump back to previous page8DigitalEnter digital or select channel9MENU/+Enter MENU page/increase value10SEARCH/-Enter SEARCH page/decrease value1110+To enter digital over 10 /Continuously press twice to have1012IRreceiverRemote receiver13EnterEnter14Split/Direction KeySwitch split/Move selected item

5

1.The Front Panel interfacefor8/16channel HDDVRis shown asbelow:TypeNameDescriptionWork stateindicatorRECWhen recording, the light is blueHDDWhen HDD is writing and reading , the light is blueBackupWhen backup files and data, the light is blueNetWhen access to network , the light is bluePlayWhen playing video, the light is bluePowerPower indicator, when connection , the light is blueCompoundbuttonP.T.Z./-1. Enter PTZ mode in live 2.Decrease the value in setupAUDIO/+1. Control voice 2. Increase the value in setupFunctionbuttonMENUEnter menu in liveINFOCheck recording data

Record manually

Play/Pause

Rewind

Fast forward

Exit/ESCBACKUPEnter backup mode in liveSEARCHEnter search modeDigital button1-9Input number 1-9 or choose camera0/10+Input number0, 10 and the above number togetherwith otherdigital keysInput buttonDirection buttonChange direction to select itemsMulti-screenChange screen display mode like1/4/9/16 channelEnter buttonConfirm selectionUSBUSB portTo connect external USB devices like USB flash, USB HDD forbackup or update firmware;1.3Rear Panel Instructions

Rear Panel for 4-chHD DVRItemNameDescription1Alarm out4-ch relay output. Connect to external alarm.2Alarm inAlarm inputs. Connect to external sensors3P/ZConnect to speed dome4K/BConnect to keyboard5CVBS portCVBS video signal output6Audio outAudio output, connect to the sound box7MIC INTalk. Connect to microphone.8Audio in4-ch Audio inputs9HD SDI Video In4-ch video inputs10HDMI portConnect to high-definition display device11VGA portVGA output, connect to monitor12LANNetwork port13USB portTo connect external USB devices like USB flash, USB HDD for backup orupdate firmware; or connect to USB mouse14DC 12VPower input

6

Fig2-3 Rear Panel for 8-CH

Fig2-4 Rear Panel for 16-CHItemNameDescription1HD SD Video inHD SDI video signal inputs.2Alarm inAlarm Inputs for connecting sensors3HDMI portConnect to high-definition display device4VGAportVGA output, connect to monitor5LANNetwork port6USB portTo connect external USB devices like USB flash drive, USB HDD forbackup or updating firmware.7GNDGrounding8K/BConnect to keyboard. A is TX+, B is TX-.9P/ZConnect to speed dome. Y is TX+, Z is TX-.10CVBSCVBS output11Audio outAudio output, connect to the sound box12MIC inTalk. Connect to microphone13Alarm outRelay Output. Connect to external alarm.14Audio inAudio input15E-SATAConnect to HDD for backup.1.4Remote Controller(Optional)It uses two AAA size batteries.iOpen the battery cover of the Remote Controller.iPlace batteries. Please take care of the polarity (+ and-).iReplace the battery cover.

Fig2-6 Remote Controller

7

ButtonFunction

Power ButtonSwitch off-to stop DVR. Use it before turning off the powerRecord ButtonTo record manually-/--/0-9 Digital ButtonInput number or choose cameraFn1 ButtonUnavailable temporarilyMulti ButtonTo choose multi screen display modeNext ButtonTo switch the live imageSEQTo enter into auto dwell modeAudioTo enable audio output in live modeSwitchTo switch the output between BNC and VGA

Direction buttonTo move cursor in setup or pan/title PTZEnter ButtonTo confirm the choice or setupMenu ButtonTo enter into menuExit ButtonTo exit the current interfaceFocus/IRIS/Zoom/PTZTo control PTZ camera. Move camera/zoom/IRIS/FocusPreset ButtonTo enter into preset setting in PTZ modeCruise ButtonTo enter into cruise setting in PTZ modeTrack ButtonTo enter into track setting in PTZ modeWiper ButtonTo enable wiper function in PTZ modeLight ButtonTo enable light function in PTZ modeClear ButtonTo return to the previous interfaceFn2 ButtonUnavailabletemporarilyInfo ButtonGet information about DVR like firmware version, HDD information

To control playback. Play/Pause/Stop/Previous Section/NextSection/Rewind/Fast ForwardSnap ButtonTo take snapshots manuallySearch ButtonTo enter into search modeCut ButtonTo set the start/end time for backup in playback modeBackup ButtonTo enter into backup modeZoom ButtonTo zoom in the imagesPIP ButtonTo enter into picture in picture setting mode

1.5Control with Mouse1.5.1Connect MouseIt supports USB mouse through the port on the rear panel, please refer toFig2.11Remote Controller.

Notice: If mouse is not detected or doesn't work, check below steps:1. Make sure the mouseis connected tothe USB mouse port not the USB port2.try another mouse1.5.2System operation by mouseThe structure of the main menu is shown inFig2.11Remote Controller.In live:Double-click left button on one camera to be full screen display.Double-click again to return to the previousscreen display.Click rightbutton to show the control bar at the bottom of the screen asFig2.11Remote Controller.Here are allcontrol and setup. Click right mouse again to hide the control bar.In setup:Click left button to enter. Click right button to cancel setup, or returnto the previous.If want to input the value, move cursor to the blank and click. An input window will appear as Fig2.12. Itsupports digitals, letters and symbols input.

8

Fig2.12Digital Numbers and Letters Input WindowUsers can change some value by the wheel, such as time. Move cursor onto the value, and roll the wheelwhen the value blinks.It supports mouse drag. I.e. Set motion detection area: click customized, hold left button and drag to set motiondetection area. Set schedule:hold left button and drag to set schedule timeIn playback:Click left button to choose the options. Click right button to return tolivemode.In backup:Click left button to choose the options. Click right button to return to previous picture.In PTZ control:Click left button to choose the buttons to control the PTZ. Click right button to return to live.

Notice:Mouse is the default tool in all the operation below unless Exceptional indication. 9

2Basic Function Instruction2.1Power On/OffBefore you power on the unit, please make sure all the connection is good.2.1.1Power onStep1:connect with the sourcepower;switch on the power button near the power port in the rear panelStep2: the device willstart to boot, and the power indicator willbecomeblueStep3: before start,a WIZARDdialogue box willpop-out(refer to belowpicture)and show some informationabout time zone andtime setup, IP information, record quick setup and HDD information page.

After the device powerson, if there is no menuor only has live image display, user can long press ESCbutton to switch.

Notice:this serial device can only display menu on VGA monitor or BNC monitor at one time, if there islive image display without menu display, please check up whether other devicehas menu display firstly, orlong press ESC key to wait for login dialog box to appear.2.1.2Power offUser can power off the device by using remote controller,keyboardand mouse.By remote controller:Step1: press Power button, theshut down window will appear, click OK, the unit will power off after a while.Step2: disconnect the powerBy keyboard and mouse:Step1:enter intoMenu, then select "System Shut Down" icon, theShut down window will appearStep2: click OK, the unit will power off after awhile.Step3: disconnect the power2.2LoginUser can login and logout the DVR system.User cannot do any other operations except changing themulti-screen display once logout.

Fig 3-1 Login

Notice:the default user name and password is "admin"and 123456"

The concrete operation steps for change password, add or delete user please refer to Fig 3.7 Usermanagement configuration for more details.

10

2.3Live preview

Fig 3-2 livepreview interfaceThe explanation of symbol in the live preview interface:symbolmeaningsymbolmeaningGreenManualrecordRedAlarmin triggerrecord

YellowMotion detection recordBlueSchedule record2.3.1Live playbackClick Playbutton to playback the recorded video. Refer to Figure3-3.Usercan do concrete operation byclick the buttons on screen.

11

Fig 3-3 live playback

3Main menu setup guideClick right mouse or press ESCbutton on the front panel, the control bar will displayon thescreen, refer toFig4-1:1SingleFull channel2Multi4ch:1/4, 8ch:1/4/9, 16ch:1/4/9/163E-ZoomLive/playback digital zoomx24AudioAudio channel setup and volume5PTZInto PTZ control mode6RecordManual record7PlaybackPlayback the nearest file8Main MenuInto main OSD9DwellChannel sequence(only 16CH)Fig4-1 main menu toolbar

ItemFunctionDescription1Playback processbarLast/nextsegmentofrecord and time process2Playbackbasic functionPlay/Pause /Stop / frameforward/fastforward/fastrewind3Display mode4ch:1/4,8ch:1/4/6/9/1+5/1+7,16ch:1/4/6/9/16/ 1+5/ 1+7/ 1+124ZoomScreen digital zoomx25ColorSetup picture color6CutEnable to select a specific part of the video andback itup on usb drive7Camera nameEnable or disable camera name display8VolumeVolume mute on/off9ReduceHide playback tool bar10Exit playbackmode11Move the playback bar in the screenFull channel switch, camera 1 ~ 4 or camera 1 ~ 8, camera 1 ~ 16

12

Click Menubutton, the interface will pop-up as Fig4-2; press MENU button on the front panel oroperate with remote controller also can display the main menu.Main OSD

Fig4-2system setup

3.1Basic configurationBasic configuration includes three sub menus: systemdate& time and DST.3.1.1SystemStep1:enter into system configurationbasic configurationsystem; refer to Fig4-3:

13

Fig4-3 basic configuration-basicStep2: in this interface user can setup the device name, device ID, video format, max networkusers, VGAresolution and language.The definitions for every parameters display as below:Device name:the name of the device. It may display on the client end or CMS that help user to recognizethe device remotely.Video format:two modes: PAL and NTSC.User can select the video format according to that of camera.Password check:enable this option, user needs to input user name and password can docorrespondingoperationswith the relevant rightin system configuration.Show time:display time in live.Showwizard:tickoff thisitem, there will display an opening wizard with time zone and time setupinformationMax network uses:set the max user amount of network connectionVGA resolution:the resolution of live display interface,range from:VGA800*600VGA1024*768VGA1280*1024,CVBSand HDMINoteWhen switch between VGA, CVBSand HDMIwill change the menu output mode, pleaseconnect to relevant monitor.Language:setup the menu language.Note: after changed the languageandvideo output, the device needs tologinagain.3.1.2Time & dateStep1: enter into system configurationbasic configurationtime & date; refer to Fig4-4:8CH

Fig4-4 basic configuration-time & dateStep2:set the date format, time format,time zone in this interface;clickoff "sync time with NTP server" to refresh NTP server date; useralso can adjust system date manuallyStep3: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" button to exit current interface.3.1.3DSTStep1: enter into system configurationbasic configurationDST; refer to Fig4-5:

Fig4-5 basic configuration-DSTStep2: in this interface, enable daylight saving time, time offset, mode, start & end month/week/date, etc.

14

Step3: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.3.2Live configurationLive configuration includesfoursubmenus: live, hostmonitor,SPOTand mask.3.2.1LiveIn this interface, user can setup camera name, adjust colors: brightness, hue, saturation and contrast.Step1: enter into system configurationlive configurationlive; refer to Fig4-6:

Fig4-6 live configurationliveStep2: tick off camera name; click "setting" button, a window will pop-up as Fig4-7:

Fig4-7 live-color adjustmentStep3: in this interface, user can adjust brightness, hue, saturation and contrast in live; click "default" buttonto resort default setting, click "OK" button to save the setting.Step4: user can setup all channels with same parameters, tick off "all", then do relevant setup.Step5: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.3.2.2MainmonitorStep1: enter into system configurationlive configurationhost monitor; refer to Fig 4-8:

Fig 4-8 live configuration-host monitor

15

Step2: select split mode: 1×12×22×33×34×4 and channelStep3: dwell time: the time interval for a certain dwell picture display switching to next dwell picture displayStep4: selected the split mode, then setup current picture group. Click

button to setup the previouschannel groups of dwell picture, click

button to set the latter channel groups of dwell picture.Step5: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.3.2.3SPOTStep1: enter into system configurationlive configurationSPOT; refer to Fig4-9:

Fig4-9 live configuration-SPOTStep2: select split mode: 1×1and channelStep3: dwell time: the time interval for a certain dwell picture display switching to next dwell picture displayStep4: selected the split mode, then setup current picture group. Click

button to setup the previouschannel groups of dwell picture, click

button to set the latter channel groups of dwell picture.Step5: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface3.2.4MaskUser can setup private mask area on the live image picture, max threes areas.

Fig 4-10 live configuration-maskSetup mask area:click Setting button, enter into live image to press left mouse and drag mouse to set maskarea, refer to below picture. ClickApply button to save the setting.Delete mask area:select a certain mask area, click left mouse to delete that mask area, click Apply button tosave the setting.

16

Setup mask areaNotice: The mask area will not be recorded on DVR. Please use this function carefully.

Live image mask area3.3Record configurationRecord configuration includesfivesub menus:enable, record bitrate,time,recyclerecordandstamp.3.3.1EnableStep1: enter into system configurationrecord configurationenable; refer to Fig 4-11:

Fig 4-11 record configuration-enableStep2: tick off record, audio and record timeStep3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.Definitions and descriptions of Record:ParameterMeaningRecordRecord switch of every channelsAudioEnable live record audio

17

3.3.2Record streamStep1:enter into system configurationrecord configurationrecordbit rate

Step2: setuprate, resolution, quality, encode and max bitstreamStep3: user can setup all channels with same parameters, tick off "All", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.Note: if the rate value set is over high the maximum resources of the device, the value will beadjusted automatically.Definitions and descriptions of Record stream:ParameterMeaningResolutionSupport 1080P,FPS4 CH HD DVR 1080P@7FPS(6FPS)8 and 16 CH HD DVR 1080P@15FPS(12FPS)QualityThe quality of recorded images. The higher the value is, theclearer the recorded image is. Six options: lowest, lower,low, medium, higher and highest.EncodeVBR and CBRMax bit streamRange from 1536kbps~12288kbps3.3.3TimeStep1: enter into system configurationrecord configurationtime; refer to Fig4-12:

Fig4-12record configuration-timePre-alarmrecord time:the record time before event happen i.e. record time before motion detection orsensor alarm is triggered.

18

Post-alarmrecord:setthe post recording time after the alarm is finished, five options:10s15s20s30sand 60s.Expiretime:the hold time of savedrecords.If the set date is overdue, the record files will be deletedautomatically.Step2:user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step3: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.

19

3.3.4StampStampUser can overlap the channel name and time stamp on video.Step1: enter into system configurationrecord configurationstamp; refer to Fig 4-13:

Fig 4-13 record configuration-stampStep2: tick off camera name, time stamp; click Set button, user can use cursor to drag the camera name andtime stamp in random positions, refer to below Figures:

Before drag after dragStep3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.3.3.5Recycle recordStep1: enter into system configurationrecord configurationrecycle record;

Step2: tick off recycle record, the recycle record function will enable, it will cover the earlier recorded filesand keep recoding when HDD is full; if disenable this function, it will stop recording when HDD is full.Step3: click "default"button to resetdefault setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.3.4Schedule configurationSchedule configuration includes three sub menus: schedule, motion and alarm.3.4.1ScheduleThe volume means the seven days of a week from Monday to Sunday, the row means 24 hours of a day.Clickthe grid todo relevant setup. Blue means checked area, gray means unchecked area.

20 Step1: enter into system configurationschedule configurationschedule; refer to Fig4-14:

Fig4-14 schedule configuration-scheduleStep2: select channel,double-clickanda dialog box will pop-up as Fig4-15, user caneditweek schedule:

Fig4-15schedule-week schedule?Click "add" button to add a certain day schedule; click "delete" button to delete the selected schedule;Copy:user can copy the specifyschedule to other dates.Click "OK" button to save the setting, click "Exit" button to exit current interface.?User can apply the schedulesettingof certain channel to other or all channels, just only select channeland click "Copy" button.Step3: click"default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.3.4.2MotionStep1: enter into system configurationschedule configurationmotion; refer to Fig4-16:

Fig4-16 schedule configuration-motionStep2: the setup steps of motion are familiar withschedule;user can refer to4.4.1Schedule for details.

21

Note: the default schedule of motion detection is full-selected, that is, the color of schedule settinginterface is blue.3.4.3SensorStep1: enter into system configurationschedule configurationalarm; refer to Fig4-17:Step2: the setup steps of alarm are familiar with schedule; user can refer to4.4.1 Schedule for details.Note: the default schedule ofsensoris full-selected, that is, the color of schedule setting interfaceis blue.

Fig4-17 schedule configuration-sensor3.5Alarm configurationAlarm configuration includes five sub menus: sensor, motion, video loss, other alarm and alarm out.3.5.1SensorSensor includesthree sub menus: basic, alarm handling and schedule.?BasicStep1: enter into system configurationalarm configurationsensorbasic; refer to Fig4-18:

Fig4-18 alarm configuration-sensor-basicStep2:enable sensor alarm, set the alarm type according to triggered alarm type. Two option: NO and NC.Step3:user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.?Alarm handlingStep1: enter into system configurationalarm configurationsensoralarm handling; refer to Fig4-19:

Fig4-19 alarm configuration-sensor-alarm handling

22
Step2: select hold time, click Trigger button,and adialog box will pop-up as Fig4-20:

Fig4-20 alarm handling-triggerStep3:tick off Buzzer, there will be triggeredbuzzeralarmout;Fullscreen alarm:when triggered alarm, there will pop up full screen alarm;Toalarm out:tick off the channel, there willbe triggered alarm out inthe designated channel.Click OKbutton to save the setting; click Exit button to exit the current interface.To record:tick off recoding channels, it will record the camera when alarmtriggered.Click OK button tosave the setting; click Exit button to exit the current interface.To P.T.Z:set linked preset and cruise for alarm. User can select any channel and multi channels as linkedchannels. ClickOK button to save the setting; clickExit button to exit the current interface.Step4: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step5: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.?ScheduleStep1: enter into system configurationalarm configurationsensorschedule; refer to Fig4-21:

Fig4-21sensor-scheduleStep2: the setup steps ofsensorscheduleare familiar with schedule; user canreferto4.4.1 Schedule fordetails.Note: the default schedule ofsensoris full-selected, that is, the color of schedule setting interfaceis blue.3.5.2MotionMotion includes two sub menus: motion and schedule.?MotionStep1: enter into system configurationalarm configurationmotion; refer to Fig4-22:

23

Fig4-22alarm configuration-motionStep2: enable motion alarm, set alarm hold timewhichmeans time interval between two adjacent detectivemotions. If there is other motion detected during the interval period which is considered continuousmovement; otherwise, it will be considered that those two adjacent detective motionsaretwo differentmotionevents.Click Trigger button, a dialog box will pop-up:Step3: thesetup steps of motion triggerare familiar with alarmhandling;user can refer to Chapter4.5.1Sensoralarm handling for more details.Step4: click Area button, a dialog box will pop-up as Fig4-23:

Fig4-23motion-areaStep5: in theArea interface, user can drag slide bar to setthesensitivity value(1-8), the default value is 4.The higher the valueisthe higher sensitivity you get. Due to the sensitivity is influenced by color and time(day or night), user can adjust its value according to the practical conditions; click

icon, set the wholearea as detection area; click icon, the set detection area will be cleared; click

icon, user cantestwhether the sensitivity value and motion area are suitableaccordinglyrefer to following picture;Click

icon, to save the setting; click icon, exit current interface. Note: when userdrag mouse to setmotion detection area, they have to click

icon to clear allset detection area firstly,and thenmaketheoperation.Step6: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step7: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.?ScheduleStep1: enter into system configurationalarm configurationschedule; refer to Fig4-24:

24

Fig3-24alarm configuration-scheduleStep2: the setup steps ofalarmschedule are familiar with schedule; user can referto4.4.1 Schedule fordetails.3.5.3Video lossStep1: enter into system configurationalarm configurationvideo loss; refer to Fig4-25:

Fig4-25alarm configuration-video lossStep2: the setup steps of video loss trigger are familiar with alarm handling; user can refer to Chapter4.5.1Sensoralarm handling for more details.Step3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting;click "exit"button to exit current interface.3.5.4Other alarm

Fig4-26 other alarmStep1:enter into system configurationother alarm; refer to Fig4-26:Step2: select a hard disk in the pull down list box, when the disk capacity is lower thanthatvalue,there willappear some text information on the lower right of the live image.Step3: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.

25

3.5.5Alarm outAlarm outincludesthreesub menus: alarmout,scheduleand buzzer?Alarm outStep1: enter into system configurationalarm out; refer to Fig4-27:

Fig4-27system configuration-alarm outStep2:in this interface, setrelay alarm out name, select holdtime which means the interval time betweenthe two adjacent alarms.Step3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.?ScheduleStep1: enter into system configurationschedule;Step2: the setup steps of alarm out schedule are familiar with schedule; user can referto4.4.1 Schedulefor details.Note: the defaultschedule of motion detection is full-selected, that is, the color of schedule settinginterface is blue.?BuzzerStep1: enter into system configurationbuzzer;(if here sets is off, all event without buzzer)Step2: tick off Buzzer, set buzzer alarm hold time3.6Network configurationNetwork configuration includes two submenus:network and network stream.3.6.1NetworkStep1: enter into system configurationnetwork configurationnetwork; refer to Fig4-28:

Fig4-28network configuration-networkStep2:HTTP port: the default value is 80. If the value changed, user needs to add the port number whentyping IP address in IE address blank .i.e. set HTTP port to 82, IP address:http://192.168.0.25, user needs toinput that address:http://192.168.0.25:82into IE browser.Server port: communication port

26

There are 3 different types to connect internet, please select an appropriate type to fit your networkenvironment.1. STATIC (FIXED) IP: Input IP address, subnet mask, gateway and DNS server manually.2. DHCP : Checkthe "Obtain IP address automatically", the device willacquireIP address, subnet mask,gatewayandDNS service.3. PPPOE :input the user name and passwordfrom ISPprovider.No matter which type you use, please click "Test" before you click "Apply" to make the setting work.Definitions and descriptions of network configuration:ParameterMeaningHTTP portThe port number of accessingIEbrowser. The defaultport is 80Server portThe port number of data. The default port is6036Static IPIPaddressThe IP address of the serverSubnet maskThe subnet mask of the serverGatewayThe gateway of the serverDNSserverThe address ofDNSserverPPPOEUsernameUser name of broad band dial-upPasswordPassword of broad band dial-upDDNSserverDDNS serverWebsite provided bydynamicdomain name supplier. Theoptional: www.meibu.comwww.dyndns.comUser nameUser name for log in the website of domain namesupplierPasswordPassword for log in the website of domain name supplier3.6.2Network streamStep1:enter into system configurationnetwork configurationsubstream; refer to Fig4-32:8CH

Fig4-32network configuration-substreamStep2: selectfps, resolution, quality, encode and max bitrateStep3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.Definitions and descriptions of network stream:

27

ParameterMeaningFPSFor 4 CH HD DVR CIF@7FPS,for 8 and 16 CH HD DVR CIF@30FPSResolutionSupport CIFQualityThe quality of the clients image. The higher the value is, theclearer the record image. Six options: lowest, lower, low,medium, higher and highest.EncodeVBR and CBRMaxbitrateRange from: 64 Kbps128 Kbps256 Kbps512 Kbps768Kbps1Mbps2 Mbps3.6.3EmailStep1: enter into system configurationnetwork configurationemail; refer to Fig 4-31:

Fig 4-31 network configuration-emailSMTP Server/Port:the name and port number of SMTP server.If your SMTP server supports the secure connection (SSL), like Gmail, please set the "Port" to 465 andcheck "SSL Check"Send address/password:sender"s email address/passwordReceive address:receiver"s email address. Here user can add at least threemail addresses.Click TEST button to test the valid of the mailbox.Attaching image amount:user can attach at most three images at one time.Snap Time Interval(s):User can select snap time interval."Strongly recommend to use Google mail (gmail)"For Example:SMTP Server: smtp.gmail.comPort: 465SSL Check: VSend Address:alan@gmail.comReceive Address1:test@yahoo.com

28

3.6.4Other settingsStep1: enable DDNS server: user needs to input user namepassword and host domain name of theregistered website, click TEST to test the effectively of relevant information.

Fig 4-32 network configuration-other settingsSTEP2: click "default" button to resort default setting; click "apply" button to save the setting; click "exit" buttonto exit current interface.Note: The domain name server that selected by user is a banding domain name of DVR. User shouldlogon the website which provided by the server supplier to register a user name and password firstly,and then apply a domain name on line for the server. After the successful apply, user can access theserver from the IE client by inputting that domain name.*Please reference Appendix C to setup DDNS function.3.7User managementconfigurationStep1: enter into system configurationuser management configuration; refer to Fig4-33:

Fig4-33user management configurationStep2: click Add button, a dialog box will pop-up as Fig4-34:

Fig4-34add-general

29

General: Input user name, password; select user type: normal and advance, input the MAC address ofthe PC; click OK button, this user will be added into the user list box; click Exit button to exit the currentinterface.Note: when the default value of binding PC MAC address is 0, the user is not bind with the specifycomputer; the, the user can log in DVR on the binding computer after set the specific binding MACaddress.Authority:a)Admin: Admin have full control of DVR. DVR could have only one admin account.b)Advance: Besides "firmware upgrade", "reset factory default", "shut down" and "change otheruser"s password", advance account could control DVR like an admin account.c)Normal: Normal account can only do "live view", "playback", "search", "backup", "log off", "viewDVR information", and "change his own password".3.8P.T.Z configurationP.T.Z configuration includes two submenus: serial port and advance?Serial portStep1: enter into system configurationP.T.Z configurationserial port; refer to Fig4-36:

Fig4-36P.T.Z configuration-serial portStep2: tick off Enable, setup thevalue ofaddress, baud rate and protocolaccording to the settings of thespeed dome.Step3: user can setup all channels with same parameters, tick off "all", then to do relevant setup.Step4: click "default" button to resort default setting; click "apply" button to save the setting; click "exit"button to exit current interface.Definitions and descriptions of network stream:ParameterMeaningAddressTheaddress ofthePTZ deviceBaud rateBaud rate of the PTZ device. Range form:110300600120024004800960019200348005760011520023040046080021600.ProtocolCommunication protocol of the PTZ device. Range from:NULLPELCOPPELCODLILINMINKINGNEONSTARVIDODSCPVISCASAMSUNGRM110HY

30
?AdvanceStep1:enterinto system configurationP.T.Z configurationadvance; refer to Fig4-37:

Fig4-37P.T.Z configuration-advanceStep2:in the Advance interface,click preset"Setting"button, a dialog box will pop-up as Fig4-38:

Fig4-38advance-preset settinga.in the preset set interface, clickSettingbutton, a dialog will pop-up as Fig 3-39:

Fig 3-39preset set-settingb.user cancontrol the dome rotates up,up left,down,right down,left , left down,right and up rightandstop rotating; adjust the rotate speed and the value of zoom, focus and iris of the dome;c. select the serial number of the preset point, set the preset name. Click Save button to save the settings,click

icon to hide the tool bar, right-key can remerge it; click

icon to exit the current interface.d. in the preset interface, click OK button to save the setting; click Exit button to exit current interface.Step3:in the Advance interface,click cruise "Setting" button, a dialog box will pop-up as Fig4-40:

31

Fig4-40cruise seta.clickAdd button to add cruise line in the list box(max 8 cruise line can be added); select a cruise line,clickSetupbutton, a dialog box will pop-up as Fig4-41:

Fig4-41cruise set-modify cruise lineb. clickAddicon to set the speed and time of preset point; select a preset point, click Deleteicon to delete that preset point; click Modifyicon to modify the setting of a preset point.User canclick

those icons toadjust the position of preset point.Click Preview button to preview thecruise line, click OK button to save the setting, click Exit button to exit current interface.c. select a preset point in the cruise line list box, click Delete button to delete that cruise line; click Clear allbutton to clear all cruise line from the list box; click OK button to save the setting; click Exit button to exitcurrent interface.Step4:inthe Advance interface,click track "Set" button, a dialog box will pop-up as Fig4-42:

Fig4-42trackseta.user can control the dome rotates up, up left, down, right down,left,left down, right and up right and stoprotating; adjust the rotate speed and the value of zoom, focus and iris of the dome;click Start Recordbutton to record the move track of PTZ, click this button again can stop record; clickStart trackbutton toplay recorded track, click this button again can stop play.;b.click

icon to hide the tool bar, right-key can remerge it; click

icon to exit the current interface.Step5:in the Advance interface,click "default" button to resort default setting; click "apply" button to savethe setting; click "exit" button to exit currentinterface.

32

4Record search&playbackand backupSearchconfigurationincludes three submenus: time search, event search and file manager.4.1Time searchStep1: enter into Search configurationtime search; refer to Fig5-1:

Fig5-1 Search configuration-time searchStep2: select channel, screen display mode, the highlight date in the calendar meanshave record dataStep3: select a date,pressSearch button, click thetimegrid to set the playstart time or input play recordtime manually. Theselected time match the blue grid.Note: the vertical column meanshours, horizontal column meanschannels.Step4: click Play

button to playbackrecord; click the relevant buttons on the screen to do operation:

Playback buttonsNote: when themonitorresolution is VGA800*600, the time search interface will appear a hidebutton, click this button, the whole interface can be expanded.4.2Event searchStep1: enter into Search configurationevent search; refer to Fig5-2:

Fig5-2 Search configuration-event searchStep2:click Search button, the searched event information will displayed in the event list box,user canselect date, channel, tick off Motion, Sensor or All accordingly.Step3: doublecheck acertainrecord file to playback.Note:when the monitor resolution is VGA800*600, the event search interface will appear a hidebutton, click this button, the whole interface can be expanded.

33

4.3File managerStep1: enter into Search configurationfile manager; refer to Fig5-3:

Fig5-3 Search configuration-file managerStep2:click Searchbutton,the searched files will be displayed in the file list box, user can select date,channels accordingly.?Lock: checked a file, click Lock button to lock this file, after that, that file will not be deleted or covered.?Unlock: checked a locked file, click Lock button to unlock this file?Delete: checkedanunlocked file, click Delete button to delete this file.Step3:tick off "All" button; user can lock/unlock or delete all files in the filemanager column.Step4: double click an unlocked item to playback.Note: when the monitor resolution is VGA800*600, the file manager interface will appear a hidebutton, click this button, the whole interface can be expanded.4.4BackupThisunit supports backup byexternalSATA DVD WriterandUSB Flash, through the USB port on the frontpanel. User also can make backup by IE browser via internet. Refer to7.3.2Remote backup.Step1: enter into backupconfiguration;refer to Fig5-4:

Fig5-4 backup configurationStep2: set the start & end time, select channels, click Search button, the searched data will be displayed inthe data backup list boxStep3: checked a data file or tick off "All" to select all data files , click Backup button, a dialog box willpop-up as Fig5-5:

34

Fig5-5 backup informationStep4: in the backup information interface, user can check the relevant information of backup files, storagetype, save file type, etc. click Apply button to starting backup.Note: when the monitor resolution is VGA800*600, the file manager interface will appear a hidebutton, click this button, the whole interface can be expanded.5Manage DVR5.1Check system informationCheck system information includes five submenus: system, event, log, network and online user.5.1.1System informationIn this interface, user can check the hardware version, MCU version, kernel version, device ID, etc. refer toFig6-1:

Fig6-1 system information5.1.2Event informationIn this interface, user cancheck record events according to set date; refer to Fig6-2:

Fig6-2 event information

35

5.1.3Log informationIn this interface, user can check relevant log information according to set date; refer to Fig6-3:

Fig6-3 log information5.1.4Network informationIn this interface, user can check relevant parameters of network; refer to Fig6-4:

Fig6-4 network information5.1.5Online informationIn this interface, user can check the details of the current connection of online users; refer to Fig6-5:

Fig6-5 online information5.1.6Manual alarmUser can check the relevant parameters of manual alarmto active emergency warning

36

5.1.6Disk managerStep1: enter into disk manager interface; refer to Fig 5-7:

Fig6-7 disk managerNote: please format theharddisk before record.If not being formatted, it will show the status of thedisk-free space, and total space show OM at the bottom of screen.Step2: click Refresh button to refresh the disk information of the list box; set the property of the disk thenclick Apply button tosave the settingStep3: checked a hard disk, click Format button to starformat.Note: all recorded files in the hard disk will be lost after formatted.5.1.7UpgradeAt present, it only supports USB update. Get the firmware from your vendor when there is a new firmwareversion, and make sure it is corresponding with the DVR. User can check the USB information in Diskmanager.5.1.8LogoffClick Log off icon, a log off dialogue box will popup, click OK button, the device will log off.If user wants tolog in again, clickicon toenter into user name and password torelogin.5.1.9Shut DownNote:DVR going to power off

37

6Remote Surveillance6.1Accessing DVRIf making remote view, the DVR must connect with LAN or internet. Then enable network server in the unit.Please refer to4.6 Network Configuration.This unit supports IE browser,withoutany client software installed.It supportsWin 7,XP and Vista.6.1.1On LANStep1: Input IP address, Subnet, Gateway. If using DHCP, please enable DHCP in both the DVR and router.Enter Menu-Information-Network, and user can check the network configuration of DVR.Step2: Enter Video to set network video parameters like resolution, frame rate etc.Step3: Open IE browser on a computer on the same LAN. Input the IP address of the DVR in IE address blankand enter.Step4: IE will download ActiveX automatically. Then a window pops up and asks for user name and password.Step5: Input name and password correctly, and enter. It will show the picture as below.

Fig 7-1 View with IE browser

Notice:If HTTP port is not 80, other number instead, need add the port number after IP address. Forexample, set HTTP port as 82, need input IP address likehttp://192.168.0.25:82.User name and password here are the same with that used on the DVR. The default is admin and 123456.6.1.2On WANThere are two ways that the DVR is connected to internet.1. Connect the DVR to internet through a router or virtual server.Step1: Input IP address, Subnet, Gateway. If using DHCP, please enable DHCP in both the DVR and router.Step2: Enter Video to set network video parameters like resolution, frame rate etc.Step3: Forward IP address and port number in Virtual Server setup of the router or virtual server. Close firewall.

Notice:Forwarding block may be different in different routers and server, please check your routermanual.If users want to utilize dynamic domain name, need apply for a domain name in a DDNS server supported bytheDVR or router. Then add to the DVR or router.Now this unit only supportswww.meibu.com,www.dyndns.com,www,no-ip.comand www.dvrdydns.comAbout the router, please check in the router manual.Step5: Open IE browser, input IP address, or dynamic domain name and enter. If HTTP port is not 80, add theport number after IP address or domain name.Step6: IE will download ActiveX automatically. Then a window pops up and asks for user name and password.Step7: Input name and password correctly, and enter to view.

Notice: If you cannot download and install ActiveX, please refer toAppendix AFAQQ7.2. Connect the DVR to internet directly.Step1: Input IP address, Subnet, Gateway gotten from your ISP. If using ADSL, please input user name andpassword, and click OK. The DVR will connect the server and show "connection succeeds".

38

Step2: The following steps are the same as STEP4-7 of the connection way above.6.2The remote live preview interface as below:

Fig 7-2 Remote live preview interfaceSymbol and function Definitions:?Channelindicator?Screen displaymode?Volume?Snappingpicture?Start manual record?Start IErecord?Bidirectionaltalk?Playback?ColorPTZ controlMaster/sub streamstatusNote: click

button to record manual and the record file will be saved in user"s PC.Screen display mode:Click the icon beside thescreen display mode, channel select dialog will appear as below:

Fig 7-3 Channel select dialogTake 8-channel DVR for example: user can tick off channels form 1-ch to 16-ch at random to display the livepictures, 8 channels can be selected at most. Thenclick OK button to confirm the setting.Snap picturesClick "Snap"

icon, the system will automatically capture pictures and save those pictures in thecomputer.User should set up the save path for those picture in the Remote Preview interfaceConfigurationLocalconfiguration.Color adjustment:Drag the slide bar to adjust Brightness, Contrast, Hue, and Saturation. Click Default to reset them to originalvalue.ButtonsDescription

Drag the scroll bar to adjust the brightness of channel 39
Dragthe scroll bar to adjust the contrast of channel Drag the scroll bar to adjust the saturation of channel

Drag the scroll bar to adjust the hue of channel

Click this button to recover the default value of brightness,contrast, saturation and hue.

Save the adjustmentPTZ controlPlease connect speed dome to the device via RS485 firstly, make sure the protocol of the speed dome issupported by the device and set the relative parameters manually. User can control the dome up, down, right,leftor stop rotating on Control Center, adjust rotation speed, Iris and zoom, focus on the dome, and set thepresets, etc.Buttons definition:ButtonsDescription

means the dome rotate up. means the dome rotate up left. means the dome rotate up right means the dome rotatedown. means the dome rotate left down. means thedome rotate right down. means the dome rotate left. means the dome rotate right. means the dome stop rotating. Drag the scroll bar to adjust rotating speed of the dome. 'Iris' button. Click button near 'Iris' button to increase light ofthe dome. Click button near 'Iris' button to decrease light ofthe dome. 'Zoom' button. Click button near 'Zoom' button to zoom in thelocale picture of this camera. Click button near 'Zoom' buttonto zoom out the locale picture of this camera. 'Focus' button. Click button near 'Focus' button to have longfocus. Click button near 'Focus' button to have short focus.

Go to the Preset

Select and do auto cruise

Track Auto scanClick the right mouse on the live interface, a pull-down menu will appear as below

Fig 7-4 right key sub menuStream:this DVR supports master stream and sub stream. Master stream has higher frame rate, max 25FPSPAL/30 FPSNTSCfor every channel, but it needs higher network bandwidth simultaneously; secondstream has low frame rate, max 6FPSPAL/7FPSNTSCfor every channel, it requires low networkbandwidth. Therefore, users can select the stream according totheir bandwidth.All to master/sub stream:set all channel to master stream or sub stream.Enable audio:enable or disenable audioFull screen:the live preview picture will display with full screen, the tool bar will be hided; double click leftmouse orclick right mouse to returnZoom in:Single channel large screen electronic amplificationLeft click the channel which needs to amplify; Click the right mouse, select Zoom in button and then click theleft mouse to amplify the image. Press left mouse to drug the cursor, user can view the image. Double-click theleft mouse to exit. Click the right mouse to return to the main interface.

40

6.3Remote playback & backup6.3.1Remote playbackClick

button to enter into record playback interface, refer to Fig 7-5:Select the record date and channels; double-click the file name in the record file list box, user can play that fileand preview the picture.

Fig 7-5 Play record file interfaceThis DVR supports remote time search, event search and file management.By Time Search:Step1:Enter into Searchtime search; refer to Fig 7-6:

Fig 7-6 time search interfaceStep2:click "Search" button. The record data will be displayed in the data information list box; the highlightdate in the area? means have record data, click those data; select the record channels in area?Step3:User can set the data playing time and display mode in the area? as requiredStep4:Select certain item from the data information list box, click "play" button to playbackStep5:Click the relevant buttons in the interface; user can do some operations such as: FF, pause, changechannel mode, research, etc. refer to Fig 7-7:

41
Fig 7-7 Time search playbackBy Event Search:Step1:Enter into Searchevent search; refer to Fig 7-8:

Fig 7-8 event search interfaceStep2:click the highlight date and select record channels and then tick off the event type: motion and sensor,click "search" buttonStep3:the events will be display in the event list box, double-click certain item to playbackFile ManagementStep1:Enter into Searchfile management; refer to Fig 7-9:

42

Fig 7-9 file management interfaceLock: select certain file item in the file list box, click "Lock" button to lock this file that ca not be deleted oroverlaidUnlock: select a locked file, click "unlock" button to unlock this fileDelete: select an unlock file, click "delete" button to delete this file from file list6.3.2Remote backupClick Backup button to enter into backup interface, refers to Fig 7-10:

Fig 7-10 remote backup interfaceStep1: select channels, set the start and end time, then click "search" button, the file information will bedisplayed in the file list boxStep2: select backup files, click "browse" button to set the save path, and then click "backup" button to startbackup. The backup files will be saved on user"s PC.6.4Remote System configurationUser can remote setup the parameters of the device. Functions of remote configurations include: basicconfiguration, live configuration, record configuration, schedule configuration, alarm configuration, networkconfiguration, PTZ configuration and user configuration. User should firstly select an item in the menu list onthe left, and then setup the relative parameters. When one user setup parameters of a certain item, otherscannot setup this one. Click Config to enter into the below interface refer to Fig 7-11:

43

Fig 7-11 remote menu setupThe sub menu lists and the options in every item are similar with those on the DVR. Please refer to Chapter 3Main Menu Setup Guide for more details.Click "Apply" button to save above settings; click "default" button will recover the original settings.6.5Remote ManagementRemote Information SearchThe system will automatically record the working condition and operation process during the period of work.User canview information, such as username, IP address and so on. Enter into INFO→Log, user can set thestart time to view the log record as follows:

Fig 7-12 Remote information search

44

7Mobile SurveillanceThis DVR supports mobile surveillanceonIphoneand android OS device, this section describes theinstallation of the program via the smartphone7.1Installation procedure onIphone deviceAt present, the software only supports version of iPhoneiOS 3.1.2 and above, if phone firmware lower thanthis version please upgrade it. Below is the operation method for iPhone mobile clients:Step1Enter into App Store function of iPhone

Step 2: Enable "search"

function to search "SuperLivePro", the required programs will be displayed onthe top of search box

Step 3: Click SuperLivePro, enter into "introduce" interface and click FREE", it will change into "INSTALL"

Step 4: Enter into iTunes Store password, click "OK"will display below interfaceNote: if it was the first time for user to operate please enter into user ID; if there is no Store account,user need to apply one.

45

Step 5:Just be patient to download and install. After installed, "SuperLivePro", icon will display. Click this icon,a function interface will appear

Step 6:Key inserver"s IP address (or domain name), user"s ID and password. ClickLogin to process. Step7:The defaultquad view windowwill be displayed.The functions descriptions as following,7.1 Click or to view different channel.7.2Click then click "OK"to capture picture.7.3Click to do local record.7.4Click to get audio from DVR.7.5Click to send voice to DVR7.6 Click to do camera color adjustment.7.7 Click to do PTZ operation.7.8 Click to view picture.7.9 Click to do local & remote playback.7.10 Click to do DVR remote setting.7.11 Click to view DVR information.7.12 Click to edit DVR list.7.13 Click to setup motion area. 46

7.2Installation procedure on Android OS smartphoneOn your smartphone click on the google play store icon

Then press on search icon on rightType SUPERLIVEPRO with your virtualkeyboard and press enter

The search result will show theavailable applicationsClick on SUPERLIVEPRO, a briefdescription of the program will be shown,click on INSTALL

47
Click on ACCEPT & DOWNLOADThe program is being downloaded on yoursmartphone, please wait

The program is being installed on yoursmartphoneThe installation is finished, click Open tolaunch the program,

48

Key your DVR IP, the username andpassword, if you want the program to keepin memoryselect REMEMBER SERVER,then click on LOGINYou are connected to the DVR, you cansee all the functions of the program

Main interface descriptionItemDescriptionPlaybackVideo file playbackImageServer photo browseLogSoftware logServer listView and edit server listLiveView camera onlineSettingsSoftware configureInformationServer and software informationHelpHelp Information about software and FAQLogoffLog off from current server

49

Live picture interface

IconDescription

One screen

Four screen

Channel configure

PTZ control

Capture

Record

Talk

Channel audio

Hide Superlivepro

50

Appendix AFAQQ1. Why the DVR cannot start after connected to the power?a. The adapter has been damaged. Please change an adapterb. The power of the adapter is not enough. Please remove the HDD to checkc. Hardware problemQ2. There is not menu output or only has live image displaya.Check up whether other devices can display menu or long pressESC key to wait for login dialog box toappear.Q2. The indicator of the DVR lights, but no output. Why?a. The power of the adapter is not enough. Please remove the HDD or change an adapter to try.b. The video format of the DVR is different from thatof the monitor.c. Connection problem. Please check the cable and the ports of monitor and DVR.Q3. Why are no images displayed on parts or all of the channels of the DVR?a. Connection problem. Please check the cable and the ports of camera and DVR.b. Camera problem. Please check the cameras.c. The video format of the DVR is different from that of the cameras. Please change DVR system format.Q4. Cannot find HDDa. The power of the adapter is not enough. Please change an adapter to try.b. Connection problem. Please check the power and data cables.c. The HDD is damaged. Change a new one.Q5. Cannot recorda. Don't format HDD. Please format it manually first.b. Don't enable record function or incorrect setup. Please refer toChapter 5 Record search &playback andbackup.c. HDD is full and not enables recycle function. Please refer to4.3 Record configuration. Chang a new HDD orenable recycle.d. The HDD is damaged. Change a new one.Q6. Cannot use mouse.a. wait1-2minutes after mouse connected.b.Not detected. Plug/unplug several times.c. The mouse is incompatible. Please change a mouse.Q7. Cannot download ActiveX control.a. IE browser blocks activeX. Please do setup following below.? Open IE browser. Click Tools-----Internet Options....

?select Security------Custom Level....Refer to Fig 7-1? Enable all the sub options under "ActiveX controls and plug-ins" refer to Fig 7-2? Then click ok to finish setup.b. Other plug-ins or anti-virusblocksActiveX. Please uninstall or close them.

51

Fig7-1Fig7-2Q8: How to deal with when DVR starts, it displays "please wait..."all the timeFirst possible reason: hard-disk cable and data cable are not well connected.Solution: Please check the connection of hard-disk cable and data cable and make sure they are wellconnected; If still not working, please unplug them and then try re-plugging again;Second possible reason: It is forced to stop because hard disk has disabled track which causes thesystemchecking hard disk cannot skipSolution: Change another new hard disk or reformat the broken oneQ9: How to input password and digital numbersThe method to input password and digital numbers is to click the box behindpasswordoritemsneeding toinput by numbers, and then the small keyboard will appear. Please select number or letter to input (the initialpassword is 123456), or you can use the digital keys in the front panel, or the digital keys on the remotecontroller.Q10: How to upgrade when added new functions or revised softwareAfter getting the upgraded software from manufacturer, please copy it into U disk, and then select "upgrade" inthe menu. If upgrading the kernel procedure, please refer to the following method: firstly insert Udisk into DVR,and then input "adwsws" in the password of system login and the system will upgrade kernel procedureautomatically. After finished, please restart DVR to achieve.Notice: Do not power off in the system upgrading process! Otherwise, it may cause that DVR cannotstart.Q11: Why is the hard disk used in a DVR identified a new hard disk if directly used to another same typeDVR? And why must we format it again?When DVR only uses one hard disk, the hard disk removed from one to another sametype DVR can worknormally without format. However, when a DVR adds to a new hard disk, it will identify the hard disk as a newone and inquire whether to format no matter whether this hard disk used or not in another same type DVRbefore. In this condition, it can be used normally after formatted according to the guide; if two or more harddisks used in different DVRs, when used in another DVR with the same type, they will be identified to be two ormore new hard disks, and all of them need to format. Ingeneral, please do not try using more disks removedfrom different DVRs into another one in case the data lose.

52

Q12: What are the minimum configurations of PC for clients connecting?PC ModuleParametersCPUIntel Celeron 2.4GMotherboardIntel 845HDD80GRAM512MVGANVIDIA GeForce MX440/FX5200ATIRADEON 7500/X300OSWindows 2000(SP 4 above ) /Wind ows XP (SP2 above)/VISTA/SEVENDirectX9.0Q13: What are the PC configurations for8-ch real time product with fully open channel mainstream?PC ModuleParametersCPUIntelCore(TM)2DuoCPUE4600MotherboardG31/P31chipHDD80GRAM1GBVGAGMA3100/NVIDIAGeForce8400/ATI RADEONHD3450OSWindows2000(SP4above)/WindowsXP(SP2above)VISTA/SEVENDirectX9.0

53

Appendix BCalculate Recording CapacityUsers can calculate the required size of hard disk according to the total recording durationand DVR recording settings. The DVR uses fixed video bit rate. The below are the details atdifferent settings for CBR.ResolutionFrameRateTotally(FPS)VideoQualityBit Rate(kbps)UsedSpace(MB/h)

1080P6(PAL)/7(NTSC)Highest12M1350Higher9M1013Medium7M788Low6M675Lower4M450Lowest1.5M16912(PAL)/15(NTSC)Highest12M2700Higher10M2250Medium8M1800Low6M1350Lower2M450Lowest1.5M338The calculation format is:Total Recording capacity =Used space per hour (MB/h)(coverage rate of hard disk) × recording time (hour) ×channel numbersFor instance, one customer uses PAL cameras, set resolutionto 1080P, video quality toLowest, frame rate to 6 fps for enabling total 4channels. He wants the unit to recordcontinuously in a month. Below is the calculation:Total Recoding capacity =169 (mb/ h) X 24( hours/day) X 30(days) X4(channels)=486720 (MB)≈475(GB)Therefore, customers need to install one SATA HDDs with 500GB for one month record.

54

Appendix CCompatible DevicesCompatible Devices1.Compatible USB drive after test.BrandCapacityA-DATA512MB, 1G, 2GBTranscend4GBKingston2GBToshiba2GBSanDisk4GB2. Compatibleexternal USBCD/DVD writers after testBrandModelLGGH24NS90

3. Compatible HDD

55

BrandModel numberCapacity

WESTERNDIGITAL

1600AAJS FW:00L7A0160GB2500AVVS FW:73M8B0250GB3200AVVS320GB5000AVDS FW:63U7B0500GB5000AVJS FW:63YJA0500GB5000AVVS FW:63M8B0500GB5000AAKS FW:00V1A0500GB5000BUDT (2.5") FW:63G8FY0500GB5000AUDX FW:63WNHY0500GB10EURS FW:630AB11TB10EVDS FW:63U8B01TB15EARS FW:00Z5B11.5TB15EURS FW:63S48Y01.5TB20EVDS FW:63T3B02TB20EARS FW:00S8B12TB2001FASS FW:00U0B02TBHITACHIHDS721616PLA380160GBHCT721025SLA380500GBHCP725050GLA380500GBHDP725050GLA3601TBSEAGATEST500DM002 (SATA3) FW:KC44500GBST3100528AS FW:CC381TBST31000524AS (SATA3)FW:JC4B1TBST2000DL003 (SATA3)FW:CC32, CC3C2TBTOSHIBAHCS5C1050DLE630FW:620 DT01ABA050V500GBDT01ABA1001TBDT01ACA1001TB

56

APPENDIX DDDNSsetup procedure (Take www.geekciti.com as an example)1.Visitwww.geekciti.comand register new account by filling each line then press submit, you need to havea valid email which will be use as username

2.Create a domain name as your convenience and choose the extension amongthe list available, then clickon REQUEST DOMAIN

57

3.If the domain exists already you will have to choose another domain name, if not you will see the belowscreen

4.Fill all setting on DVR then click "Test" to verify. Then click "Apply" to Finish DVR network setting. (Menu->Network-> Other Settings)

DDNS:enabledDDNSType:mintdnsServer www.geekciti.comUser Name: dvrtest110@gmail.com (your account onwww.geekcitiquotesdbs_dbs50.pdfusesText_50

[PDF] dvr h264 manuel

[PDF] dvr h264 mot de passe oublié

[PDF] dvr h264 network

[PDF] dyna info

[PDF] dynamique cours pdf

[PDF] dynamique des fluides exercices corrigés

[PDF] dynamique du point matériel exercices corrigés

[PDF] dynamique géographique des grandes aires continentales

[PDF] dynamique physique cours

[PDF] dynamique physique exercices corrigés

[PDF] dynamiques territoriales etats unis croquis

[PDF] dysgraphie

[PDF] dysgraphie molle

[PDF] dysorthographie et dysgraphie 285 exercices comprendre évaluer remédier s entraîner

[PDF] dysorthographie pdf