[PDF] Lecture Note On Microprocessor and Microcontroller Theory and

View - Download Lecture Note On Microprocessor and Microcontroller Theory and

Previous PDF

Next PDF

Lecture Note

On

Microprocessor and Microcontroller

Theory and Applications

Subject Code:BEE-1501

Semester: 5th

Branch: EE and EEE

Syllabus

Disclaimer

This document does not claim any originality and cannot be used as a substitute for prescribed textbooks. The information presented here is merely a collection by the committee members for their respective teaching assignments. Various sources as mentioned at the end of the document as well as freely available material from internet were consulted for preparing this document. The ownership of the information lies with the respective authors or institutions. Further, this document is not intended to be used for commercial purpose and the committee members are not accountable for any issues, legal, or otherwise, arising out of this document. The committee members make no representations or warranties with respect to the accuracy or completeness of the contents of this document and specially disclaim any implied warranties of merchantability or fitness for a particular purpose. The committee members shall not be liable for any loss or profit or any other commercial damages, including but not limited to special, incidental, consequential, or other damages.

MODULE: 1

1. INTRODUCTION TO MICROPROCESSOR AND MICROCOMPUTER

ARCHITECTURE:

A microprocessor is a programmable electronics chip that has computing and decision making capabilities similar to central processing unit of a computer. Any microprocessor- based systems having limited number of resources are called microcomputers. Nowadays, microprocessor can be seen in almost all types of electronics devices like mobile phones, printers, washing machines etc. Microprocessors are also used in advanced applications like radars, satellites and flights. Due to the rapid advancements in electronic industry and large scale integration of devices results in a significant cost reduction and increase application of microprocessors and their derivatives.

Fig.1 Microprocessor-based system

Bit: A bit is a single binary digit.

Word: A word refers to the basic data size or bit size that can be processed by the arithmetic and logic unit of the processor. A 16-bit binary number is called a word in a 16-bit processor. Bus: A bus is a group of wires/lines that carry similar information. System Bus: The system bus is a group of wires/lines used for communication between the microprocessor and peripherals. Memory Word: The number of bits that can be stored in a register or memory element is called a memory word. Address Bus: It carries the address, which is a unique binary pattern used to identify a memory location or an I/O port. For example, an eight bit address bus has eight lines and thus it can address 28 = 256 different locations. The locations in hexadecimal format can be written as 00H FFH. Data Bus: The data bus is used to transfer data between memory and processor or between I/O device and processor. For example, an 8-bit processor will generally have an 8-bit data bus and a 16-bit processor will have 16-bit data bus. Control Bus: The control bus carry control signals, which consists of signals for selection of memory or I/O device from the given address, direction of data transfer and synchronization of data transfer in case of slow devices. A typical microprocessor consists of arithmetic and logic unit (ALU) in association with control unit to process the instruction execution. Almost all the microprocessors are based on the principle of store-program concept. In store-program concept, programs or instructions are sequentially stored in the memory locations that are to be executed. To do any task using a microprocessor, it is to be programmed by the user. So the programmer must have idea about its internal resources, features and supported instructions. Each microprocessor has a set of instructions, a list which is provided by the microprocessor manufacturer. The instruction set of a microprocessor is provided in two forms: binary machine code and mnemonics. Microprocessor communicates and operates in binary numbers 0 and 1. The set of instructions in the form of binary patterns is called a machine language and it is difficult for us to understand. Therefore, the binary patterns are given abbreviated names, called mnemonics, which forms the assembly language. The conversion of assembly-level language into binary machine-level language is done by using an application called assembler.

Technology Used:

The semiconductor manufacturing technologies used for chips are:

Transistor-Transistor Logic (TTL)

Emitter Coupled Logic (ECL)

Complementary Metal-Oxide Semiconductor (CMOS)

Classification of Microprocessors:

Based on their specification, application and architecture microprocessors are classified.

Based on size of data bus:

4-bit microprocessor

8-bit microprocessor

16-bit microprocessor

32-bit microprocessor

Based on application:

General-purpose microprocessor- used in general computer system and can be used by programmer for any application. Examples, 8085 to Intel Pentium. Microcontroller- microprocessor with built-in memory and ports and can be programmed for any generic control application. Example, 8051. Special-purpose processors- designed to handle special functions required for an application. Examples, digital signal processors and application-specific integrated circuit (ASIC) chips.

Based on architecture:

Reduced Instruction Set Computer (RISC) processors Complex Instruction Set Computer (CISC) processors

2. 8085 MICROPROCESSOR ARCHITECTURE

The 8085 microprocessor is an 8-bit processor available as a 40-pin IC package and uses +5 V for power. It can run at a maximum frequency of 3 MHz. Its data bus width is 8-bit and address bus width is 16-bit, thus it can address 216 = 64 KB of memory. The internal architecture of 8085 is shown is Fig. 2.

Fig. 2 Internal Architecture of 8085

Arithmetic and Logic Unit

The ALU performs the actual numerical and logical operations such as Addition (ADD), Subtraction (SUB), AND, OR etc. It uses data from memory and from Accumulator to perform operations. The results of the arithmetic and logical operations are stored in the accumulator.

Registers

The 8085 includes six registers, one accumulator and one flag register, as shown in Fig. 3. In addition, it has two 16-bit registers: stack pointer and program counter. They are briefly described as follows. The 8085 has six general-purpose registers to store 8-bit data; these are identified as B, C, D, E, H and L. they can be combined as register pairs - BC, DE and HL to perform some

16-bit operations. The programmer can use these registers to store or copy data into the

register by using data copy instructions.

Fig. 3 Register organisation

Accumulator

The accumulator is an 8-bit register that is a part of ALU. This register is used to store 8-bit data and to perform arithmetic and logical operations. The result of an operation is stored in the accumulator. The accumulator is also identified as register A.

Flag register

The ALU includes five flip-flops, which are set or reset after an operation according to data condition of the result in the accumulator and other registers. They are called Zero (Z), Carry (CY), Sign (S), Parity (P) and Auxiliary Carry (AC) flags. Their bit positions in the flag register are shown in Fig. 4. The microprocessor uses these flags to test data conditions.

Fig. 4 Flag register

For example, after an addition of two numbers, if the result in the accumulator is larger than

8-bit, the flip-flop uses to indicate a carry by setting CY flag to 1. When an arithmetic

operation results in zero, Z flag is set to 1. The S flag is just a copy of the bit D7 of the accumulator. A negative num complement representation. The AC flag is set to 1, when a carry result from bit D3 and passes to bit D4. The P flag is set to 1, when the result in accumulator contains even number of 1s.

Program Counter (PC)

This 16-bit register deals with sequencing the execution of instructions. This register is a memory pointer. The microprocessor uses this register to sequence the execution of the instructions. The function of the program counter is to point to the memory address from which the next byte is to be fetched. When a byte is being fetched, the program counter is automatically incremented by one to point to the next memory location.

Stack Pointer (SP)

The stack pointer is also a 16-bit register, used as a memory pointer. It points to a memory location in R/W memory, called stack. The beginning of the stack is defined by loading 16- bit address in the stack pointer.

Instruction Register/Decoder

It is an 8-bit register that temporarily stores the current instruction of a program. Latest instruction sent here from memory prior to execution. Decoder then takes instruction and decodes or interprets the instruction. Decoded instruction then passed to next stage.

Control Unit

Generates signals on data bus, address bus and control bus within microprocessor to carry out the instruction, which has been decoded. Typical buses and their timing are described as follows: Data Bus: Data bus carries data in binary form between microprocessor and other external units such as memory. It is used to transmit data i.e. information, results of arithmetic etc between memory and the microprocessor. Data bus is bidirectional in nature. The data bus width of 8085 microprocessor is 8-bit i.e. 28 combination of binary digits and are typically identified as D0 D7. Thus size of the data bus determines what arithmetic can be done. If only 8-bit wide then largest number is

11111111 (255 in decimal). Therefore, larger numbers have to be broken down into

chunks of 255. This slows microprocessor. Address Bus: The address bus carries addresses and is one way bus from microprocessor to the memory or other devices. 8085 microprocessor contain 16-bit address bus and are generally identified as A0 - A15. The higher order address lines (A8 A15) are unidirectional and the lower order lines (A0 A7) are multiplexed (time-shared) with the eight data bits (D0 D7) and hence, they are bidirectional. Control Bus: Control bus are various lines which have specific functions for coordinating and controlling microprocessor operations. The control bus carries control signals partly unidirectional and partly bidirectional. The following control and status signals are used by 8085 processor: I. ALE (output): Address Latch Enable is a pulse that is provided when an address appears on the AD0 AD7 lines, after which it becomes 0. II. RD (active low output): The Read signal indicates that data are being read from the selected I/O or memory device and that they are available on the data bus. III. WR (active low output): The Write signal indicates that data on the data bus are to be written into a selected memory or I/O location. IV. MIO/ (output): It is a signal that distinguished between a memory operation and an I/O operation. When MIO/ = 0 it is a memory operation and MIO/

1 it is an I/O operation.

V. S1 and S0 (output): These are status signals used to specify the type of operation being performed; they are listed in Table 1.

Table 1 Status signals and associated operations

S1 S0 States

0 0 Halt

0 1 Write

1 0 Read

1 1 Fetch

The schematic representation of the 8085 bus structure is as shown in Fig. 5. The microprocessor performs primarily four operations: I. Memory Read: Reads data (or instruction) from memory. II. Memory Write: Writes data (or instruction) into memory.

III. I/O Read: Accepts data from input device.

IV. I/O Write: Sends data to output device.

The 8085 processor performs these functions using address bus, data bus and control bus as shown in Fig. 5.

Fig. 5 The 8085 bus structure

3. 8085 PIN DESCRIPTION

Properties:

It is a 8-bit microprocessor

Manufactured with N-MOS technology

40 pin IC package

It has 16-bit address bus and thus has 216 = 64 KB addressing capability.

Operate with 3 MHz single-phase clock

+5 V single power supply The logic pin layout and signal groups of the 8085nmicroprocessor are shown in Fig. 6. All the signals are classified into six groups:

Address bus

Data bus

Control & status signals

Power supply and frequency signals

Externally initiated signals

Serial I/O signals

Fig. 6 8085 microprocessor pin layout and signal groups

Address and Data Buses:

A8 A15 (output, 3-state): Most significant eight bits of memory addresses and the eight bits of the I/O addresses. These lines enter into tri-state high impedance state during HOLD and HALT modes. AD0 AD7 (input/output, 3-state): Lower significant bits of memory addresses and the eight bits of the I/O addresses during first clock cycle. Behaves as data bus during third and fourth clock cycle. These lines enter into tri-state high impedance state during HOLD and HALT modes.

Control & Status Signals:

ALE: Address latch enable

RD : Read control signal. WR : Write control signal. MIO/ , S1 and S0 : Status signals.

Power Supply & Clock Frequency:

Vcc: +5 V power supply

Vss: Ground reference

X1, X2: A crystal having frequency of 6 MHz is connected at these two pins

CLK: Clock output

Externally Initiated and Interrupt Signals:

INRESET

: When the signal on this pin is low, the PC is set to 0, the buses are tri- stated and the processor is reset. RESET OUT: This signal indicates that the processor is being reset. The signal can be used to reset other devices. READY: When this signal is low, the processor waits for an integral number of clock cycles until it goes high. HOLD: This signal indicates that a peripheral like DMA (direct memory access) controller is requesting the use of address and data bus.

HLDA: This signal acknowledges the HOLD request.

INTR: Interrupt request is a general-purpose interrupt.quotesdbs_dbs20.pdfusesText_26

[PDF] 8085 instruction set and assembly language programming

[PDF] 8085 instruction set gaonkar ppt

[PDF] 8085 instruction set pdf

[PDF] 8085 instruction set with examples ppt

[PDF] 8085 microprocessor architecture

[PDF] 8085 microprocessor assembly language programs pdf

[PDF] 8085 microprocessor book pdf for engineering

[PDF] 8085 microprocessor instruction set opcodes pdf

[PDF] 8085 microprocessor instruction set table pdf

[PDF] 8085 microprocessor instruction set with machine cycle pdf

[PDF] 8085 microprocessor pdf

[PDF] 8085 microprocessor pdf notes

[PDF] 8085 microprocessor programming tutorial pdf

[PDF] 8085 microprocessor programs examples

[PDF] 8085 microprocessor programs examples pdf