BaseControl®









Pressure transmitter PASCAL CV4 - for diaphragm seal operation

DB_D4-016-7_en_12.01 2020-12 Pressure transmitter PASCAL CV4. Page 2/10 0.05 bar. 2 bar. 3 bar rel. 30 mbar abs. -1...4 bar rel. 0.2 bar. 5 bar.
Labom PRESSURE TRANSMITTER PASCAL Series CV datasheet


Pressure transmitter/Pressure switch PASCAL CS

0…1 bar to 0…6 bar abs. The pressure transmitter/pressure switch PASCAL CS is ... 10 bar. A1054. 0...16 bar. 10 bar. A1055. 0...2
Datasheet PASCAL CS


Pressure transmitter PASCAL CV4 - with threaded connection Type

0…1 bar *. 0.05 bar. 2 bar. 3 bar. 100 mbar abs. Piezoresistive. 0…4 bar *. 0.2 bar. 5 bar. 10 bar. 100 mbar abs. 0…16 bar *. 0.8 bar. 17 bar. 60 bar.
D CV EN


Pressure transmitter PASCAL CV4 - for diaphragm seal operation

DB_D4-016-7_en_13.00 2022-04 Pressure transmitter PASCAL CV4. Page 2/8. Technical data 200 bar. 100 mbar abs. -0.25…0.25 bar. 0.0125 bar. 05 bar. 1 bar.
D CV EN





Differential pressure transmitter PASCAL Ci4 Delta P - for

5 bar. 75 bar. 1 bar. 0.01 bar. 2 bar. 20 bar. 10 bar. 75 bar. 4 bar. 0.04 bar. 5 bar. 50 bar. 25 bar. 75 bar. 16 bar. 0.16 bar. 17 bar. 100 bar. 75 bar.
datablad remote seal


PA Bar Admission Rules

Jan 4 2022 "Pa.B.A.R.". Adopted July 1
rules


Pressure transmitter PASCAL CV

measuring spans 1 min. span max. span overload limits vakuum tight at < 50 °C 2. 0.4 bar. 5:1. -0.4…0.4 bar. 80 mbar. 0.8 bar. 1 bar. 400 mbar abs. 1 bar.
datablad


Pressure transmitter PASCAL Ci4 - for diaphragm seal operation

100 bar. -. 100 mbar abs. -025…0
D CI EN





BaseControl®

Safe operation with compressed gases up to 230 bar Acetylene 25/15 bar. - Propane 25/4 bar ... PA. CR. Inlet/Outlet connection. Gas specific connection.
BASECONTROL DIN EN


Pressure transmitter PASCAL Ci4 - with threaded connection Type

0…1 bar *. 0.01 bar. 2 bar. 3 bar. -. 100 mbar abs. Piezoresistive. 0…4 bar *. 0.04 bar. 5 bar. 10 bar. -. 100 mbar abs. 0…16 bar *. 0.16 bar. 17 bar.
D CI EN


210493 BaseControl®

EDITION 1/2016

CYLINDER REGULATOR

Base

Control®

• Cylinder regulator conforming to ISO 2503 - Small in size but robust in features - Fits to all cylinders from 5 liters to 50 liters - Safe operation with compressed gases up to 230 bar cylinder ? lling pressure - Gas speci? c cylinder connection according to standards • Available in following variants: - Oxygen 230/10 bar - Acetylene 25/1,5 bar - Propane 25/4 bar - Ar/Ar-CO 2 mixtures 230/24 l/min - CO 2

200/24 l/min

• Oxygen adiabatic shock safety • Regulating valve protected against mechanical particles of size 50µm by inlet ? lter • Protection of the low pressure part with integrated pressure relief valve • Pressure values are shown on the gauges in three major pressure units scales: Bar, kPa, psi • Flow gauge showing the value in litres per minute (l/min) • Useful in various applications as e.g.: - Shielding gas arc welding - Flame welding - Oxy-fuel cutting - Flame brazing - Di? erent heating processes - Flame spraying DIN www.gcegroup.com

Art. Nr. 735100001112. Edition 1/2016. Alterations are subject to change without notice. 30082016mk © 2016

MEASUREMENTSTECHNICAL DATA

BodyBrass forged

BonnetZn/Al alloy Die-casted

Stems, nuts nad ?ttingsBrass

Diaphragm

EPDMNBR

Seat sealingPACR

Inlet/Outlet connection Gas speci?c connection

Maximal inlet pressure

230bar230bar200bar25bar25bar

Outlet pressure range 0-10bar 0-24l/min1,5bar4bar

Temperature rangefrom -20°C to 60°C

WeightApprox. acc.to gas variant: 1,18 kg

ISO 2503 Class

3202021

OXYGEN Ar, Ar/CO

2 CO 2

ACETYLENE PROPANE

PRODUCT DESCRIPTION

1 CYLINDER CONNECTION

Gas speci?c inlet connection is used on each version of the GCE BaseControl®. Quality sealing faces and brass nut ensure gas tight connection with cylinder valve.

2 INLET STEM

Inlet stem is made of brass. It is designed for up to 230 bar inlet pressure and contain shigh-pressure sintered ?lter.

3 PRESSURE RELIEF VALVE

PRV is the safety device protecting low-pressure chamber of the regulator against over pressurazing from high-pressure chamber. PRV relieves out of the regulator the pres sure which could exeeded adjusted safe value in case of malfunction or accident.

4 OUTLET CONNECTION

The outlet of the GCE BaseControl® is prepared to make gas-tight connection with out- let ?ashback arrestor or hose nipple.

5 HANDWHEEL

Ergonomic plastic hand wheel allowing the operator to correctly adjust the outlet pres sure or ?ow rate. The pressure adjustment system gives the possibility to set the opti mal outlet parameter according to application request.

6 PRESSURE GAUGES

Both high pressure and low pressure gauges show the value on three scales: bar, kPa (kilo pascal) and psi (pound per square inch). The connection to the regulator body is

G1/4". Gauges 50mm diameter conform to ISO 5171.

7 BODY AND BONNET

The body of the GCE BaseControl® is forged from pressure resistant brass. The channels and faces inside the body are machined using latest technology of CNC machines and tools. The bonnet is Die-casted from the Zn-Al alloy to prepare optimal space for pres sure adjustment system and other internal components. Connection between body and bonnet is designed to give high resistance against external and internal stress. 1 2 456
7 3

Rear view

EDITION 1/2016

CYLINDER REGULATOR

Base

Control®

• Cylinder regulator conforming to ISO 2503 - Small in size but robust in features - Fits to all cylinders from 5 liters to 50 liters - Safe operation with compressed gases up to 230 bar cylinder ? lling pressure - Gas speci? c cylinder connection according to standards • Available in following variants: - Oxygen 230/10 bar - Acetylene 25/1,5 bar - Propane 25/4 bar - Ar/Ar-CO 2 mixtures 230/24 l/min - CO 2

200/24 l/min

• Oxygen adiabatic shock safety • Regulating valve protected against mechanical particles of size 50µm by inlet ? lter • Protection of the low pressure part with integrated pressure relief valve • Pressure values are shown on the gauges in three major pressure units scales: Bar, kPa, psi • Flow gauge showing the value in litres per minute (l/min) • Useful in various applications as e.g.: - Shielding gas arc welding - Flame welding - Oxy-fuel cutting - Flame brazing - Di? erent heating processes - Flame spraying DIN www.gcegroup.com

Art. Nr. 735100001112. Edition 1/2016. Alterations are subject to change without notice. 30082016mk © 2016

MEASUREMENTSTECHNICAL DATA

BodyBrass forged

BonnetZn/Al alloy Die-casted

Stems, nuts nad ?ttingsBrass

Diaphragm

EPDMNBR

Seat sealingPACR

Inlet/Outlet connection Gas speci?c connection

Maximal inlet pressure

230bar230bar200bar25bar25bar

Outlet pressure range 0-10bar 0-24l/min1,5bar4bar

Temperature rangefrom -20°C to 60°C

WeightApprox. acc.to gas variant: 1,18 kg

ISO 2503 Class

3202021

OXYGEN Ar, Ar/CO

2 CO 2

ACETYLENE PROPANE

PRODUCT DESCRIPTION

1 CYLINDER CONNECTION

Gas speci?c inlet connection is used on each version of the GCE BaseControl®. Quality sealing faces and brass nut ensure gas tight connection with cylinder valve.

2 INLET STEM

Inlet stem is made of brass. It is designed for up to 230 bar inlet pressure and contain shigh-pressure sintered ?lter.

3 PRESSURE RELIEF VALVE

PRV is the safety device protecting low-pressure chamber of the regulator against over pressurazing from high-pressure chamber. PRV relieves out of the regulator the pres sure which could exeeded adjusted safe value in case of malfunction or accident.

4 OUTLET CONNECTION

The outlet of the GCE BaseControl® is prepared to make gas-tight connection with out- let ?ashback arrestor or hose nipple.

5 HANDWHEEL

Ergonomic plastic hand wheel allowing the operator to correctly adjust the outlet pres sure or ?ow rate. The pressure adjustment system gives the possibility to set the opti mal outlet parameter according to application request.

6 PRESSURE GAUGES

Both high pressure and low pressure gauges show the value on three scales: bar, kPa (kilo pascal) and psi (pound per square inch). The connection to the regulator body is

G1/4". Gauges 50mm diameter conform to ISO 5171.

7 BODY AND BONNET

The body of the GCE BaseControl® is forged from pressure resistant brass. The channels and faces inside the body are machined using latest technology of CNC machines and tools. The bonnet is Die-casted from the Zn-Al alloy to prepare optimal space for pres sure adjustment system and other internal components. Connection between body and bonnet is designed to give high resistance against external and internal stress. 1 2 456
7 3

Rear view


12345 Next